| Author |
Message |
grimreaper
Joined: Sat Aug 16, 2008 11:30 pm Posts: 121 Location: port macquarie nsw
|
 Posted: Mon Sep 22, 2008 12:28 pm |
|
hi i am looking at geting an rebuild kit as i have got an noterh transfer case, as the one i have now is leackign oil and very bad whine to it .
but what i want to know is this ( here )kit going to have all the stuff i need and is it an good kit
|
|
|
|
|
Damo
az supporter
Joined: Sat Jul 22, 2006 11:30 pm Posts: 4661 Location: Brisbane
|
Posted: Mon Sep 22, 2008 1:57 pm |
|
grimreaper wrote: hi i am looking at geting an rebuild kit as i have got an noterh transfer case, as the one i have now is leackign oil and very bad whine to it . but what i want to know is this ( here )kit going to have all the stuff i need and is it an good kit What you probably want to do is pull down the spare case that you have and see what parts in there need replacging. Bearings and seals are the main parts that will wear, but you also want to check the condition of the counter shaft, and the needle roller bearings that run on the counter shaft. There are also thrust washers that sit at each end of the counter shaft.
Have a look at this attachment, it's from the Trail Gear web site and is an excellent guide to pulling down and reassembling a transfer case.
You do not have the required permissions to view the files attached to this post.
_________________
SJ50.4.LYF
|
|
|
|
|
grimreaper
Joined: Sat Aug 16, 2008 11:30 pm Posts: 121 Location: port macquarie nsw
|
Posted: Mon Sep 22, 2008 2:37 pm |
|
|
thx ,that was what i was planing on doing is to rebuild the spare case and then when it is all good put it in the 4x4
|
|
|
|
|
grimreaper
Joined: Sat Aug 16, 2008 11:30 pm Posts: 121 Location: port macquarie nsw
|
Posted: Mon Sep 22, 2008 9:37 pm |
|
Damo wrote: grimreaper wrote: hi i am looking at geting an rebuild kit as i have got an noterh transfer case, as the one i have now is leackign oil and very bad whine to it . but what i want to know is this ( here )kit going to have all the stuff i need and is it an good kit What you probably want to do is pull down the spare case that you have and see what parts in there need replacging. Bearings and seals are the main parts that will wear, but you also want to check the condition of the counter shaft, and the needle roller bearings that run on the counter shaft. There are also thrust washers that sit at each end of the counter shaft. Have a look at this attachment, it's from the Trail Gear web site and is an excellent guide to pulling down and reassembling a transfer case. just pulled the t.case down and most of it looks fine ,so now with the kit i linked to in my op would that be all i need to put it back to gether
|
|
|
|
|
Damo
az supporter
Joined: Sat Jul 22, 2006 11:30 pm Posts: 4661 Location: Brisbane
|
Posted: Mon Sep 22, 2008 9:45 pm |
|
grimreaper wrote: Damo wrote: grimreaper wrote: hi i am looking at geting an rebuild kit as i have got an noterh transfer case, as the one i have now is leackign oil and very bad whine to it . but what i want to know is this ( here )kit going to have all the stuff i need and is it an good kit What you probably want to do is pull down the spare case that you have and see what parts in there need replacging. Bearings and seals are the main parts that will wear, but you also want to check the condition of the counter shaft, and the needle roller bearings that run on the counter shaft. There are also thrust washers that sit at each end of the counter shaft. Have a look at this attachment, it's from the Trail Gear web site and is an excellent guide to pulling down and reassembling a transfer case. just pulled the t.case down and most of it looks fine ,so now with the kit i linked to in my op would that be all i need to put it back to gether Yeah sounds like you're good to go!
_________________
SJ50.4.LYF
|
|
|
|
|
mrw82
az supporter
Joined: Tue Jul 03, 2007 11:30 pm Posts: 1350 Location: stuck in a hole. not off road, just deception bay.
Vehicle: snotbox, 84 LWB sierra 1 litre
|
Posted: Tue Sep 23, 2008 1:27 am |
|
|
thats a pretty good price for that kit too $159 inc shipping.
I paid pretty much that getting it all separately, most of it at trade prices too...
|
|
|
|
|
grimreaper
Joined: Sat Aug 16, 2008 11:30 pm Posts: 121 Location: port macquarie nsw
|
Posted: Tue Sep 23, 2008 12:45 pm |
|
mrw82 wrote: thats a pretty good price for that kit too $159 inc shipping.
I paid pretty much that getting it all separately, most of it at trade prices too...
so that kit includs all the stuff to rebuild it
|
|
|
|
|
mrw82
az supporter
Joined: Tue Jul 03, 2007 11:30 pm Posts: 1350 Location: stuck in a hole. not off road, just deception bay.
Vehicle: snotbox, 84 LWB sierra 1 litre
|
Posted: Tue Sep 23, 2008 11:19 pm |
|
|
yeah mate that was all I used so unless somethings broken in your case that shouls be all you need.
|
|
|
|
|
|
