auszookers.com • View topic - Rotary table/ bender stand.

Board index » Talking About Stuff » I made it and fabrication

Rotary table/ bender stand.

Page 1 of 1

[ 15 posts ]

Print view

Previous topic | Next topic

Author

Message

Fatzook

az supporter

Joined: Sat Oct 27, 2007 11:30 pm
Posts: 14977
Location: The Hills
Vehicle: Vitara, NGV

Posted: Sat Jun 08, 2013 6:47 pm

I found a use for the old NT 1.3 diff housings and axles!!!

Just cut the bearing housing off the end of the axle housing, and indexed it into some 75 x 5 SHS. Then the old axle is docked just past the bearing retainer, and dropped into the end.

More pics tomorrow.

_________________
2013 GV
1998 SV420 ute

atari4x4

az supporter

Joined: Mon Dec 11, 2006 10:30 pm
Posts: 34843
Location: East Radelayed
Vehicle: SV420+SV620 Vitara's

Posted: Sat Jun 08, 2013 6:51 pm

i hope you're going to fit some LED's so you know how far to rotate it. :lol:

_________________
You're just hating because you don't understand

Fatzook

az supporter

Joined: Sat Oct 27, 2007 11:30 pm
Posts: 14977
Location: The Hills
Vehicle: Vitara, NGV

Posted: Sat Jun 08, 2013 6:51 pm

Fuck off idiot. This place is worse than Boost cruising!

_________________
2013 GV
1998 SV420 ute

Rusho

Tubby Elfsdong

Joined: Sun Aug 02, 2009 11:30 pm
Posts: 6501
Location: Northside, Brisbane
Vehicle: Coily Sierra

Posted: Sat Jun 08, 2013 6:56 pm

Fatzook wrote:

Fuck off idiot. This place is worse than Boost cruising!

_________________
Shep is a closet jimny lover!!!!

Fatzook

az supporter

Joined: Sat Oct 27, 2007 11:30 pm
Posts: 14977
Location: The Hills
Vehicle: Vitara, NGV

Posted: Sat Jun 08, 2013 6:56 pm

The post drops onto a 65x5SHS spigot in the bottom of the hole in the middle of the floor.

_________________
2013 GV
1998 SV420 ute

bigrig91

Joined: Mon May 11, 2009 11:30 pm
Posts: 1308
Location: Redcliffe
Vehicle: 96 LWB Vit, 2.5L powerhouse

Posted: Sat Jun 08, 2013 7:00 pm

Less picture taking more using the bender haha. Wish the shed looked like that now ^^^

atari4x4

az supporter

Joined: Mon Dec 11, 2006 10:30 pm
Posts: 34843
Location: East Radelayed
Vehicle: SV420+SV620 Vitara's

Posted: Sat Jun 08, 2013 7:00 pm

Rusho wrote:

Fatzook wrote:

Fuck off idiot. This place is worse than Boost cruising!

_________________
You're just hating because you don't understand

31zook

Joined: Tue Mar 24, 2009 10:30 pm
Posts: 9242
Location: maito
Vehicle: <3 Edna <3

Posted: Thu Jun 13, 2013 6:27 pm

Hydro bender?

Fatzook

az supporter

Joined: Sat Oct 27, 2007 11:30 pm
Posts: 14977
Location: The Hills
Vehicle: Vitara, NGV

Posted: Thu Jun 13, 2013 6:30 pm

31zook wrote:

Hydro bender?

Hydro/ pnuematic.

_________________
2013 GV
1998 SV420 ute

31zook

Joined: Tue Mar 24, 2009 10:30 pm
Posts: 9242
Location: maito
Vehicle: <3 Edna <3

Posted: Sun Jun 16, 2013 8:49 am

Sweet! Was thinking the first bend you tried with it on a bearing would be funny to watch :lol:

missmyljdaze

Joined: Tue Jul 05, 2011 7:16 am
Posts: 2323
Location: perth

Posted: Sun Jun 16, 2013 1:54 pm

if you plan on using the bolt holes in the bearing housing's flange at any time, it might be a good idea to turn it 45 degrees before you weld it in place.

stephen

Fatzook

az supporter

Joined: Sat Oct 27, 2007 11:30 pm
Posts: 14977
Location: The Hills
Vehicle: Vitara, NGV

Posted: Sun Jun 16, 2013 5:18 pm

31zook wrote:

Sweet! Was thinking the first bend you tried with it on a bearing would be funny to watch :lol:

Speedworks bender. Its verticle :wink:

_________________
2013 GV
1998 SV420 ute

Fatzook

az supporter

Joined: Sat Oct 27, 2007 11:30 pm
Posts: 14977
Location: The Hills
Vehicle: Vitara, NGV

Posted: Sun Jun 16, 2013 5:19 pm

missmyljdaze wrote:

if you plan on using the bolt holes in the bearing housing's flange at any time, it might be a good idea to turn it 45 degrees before you weld it in place.

stephen

Nope. Already welded up. I just need to add a locking pin from the base to the table top to stop it rotating once in position.

_________________
2013 GV
1998 SV420 ute

Teracis

Joined: Sat Dec 11, 2010 10:03 pm
Posts: 2261
Location: Gold Coast
Vehicle: Daisy

Posted: Fri Jun 21, 2013 8:29 pm

Nice slab on the floor bloke, looks much better than the dust/mudbowl!

Fatzook

az supporter

Joined: Sat Oct 27, 2007 11:30 pm
Posts: 14977
Location: The Hills
Vehicle: Vitara, NGV

Posted: Fri Jun 21, 2013 11:45 pm

Teracis wrote:

Nice slab on the floor bloke, looks much better than the dust/mudbowl!

I'll get a pic of it in the morning. The floor of a zulu's hut would be cleaner!

_________________
2013 GV
1998 SV420 ute

Page 1 of 1

[ 15 posts ]

Board index » Talking About Stuff » I made it and fabrication

Who is online

Users browsing this forum: No registered users and 3 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum