| Author |
Message |
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
 Posted: Wed Aug 15, 2012 2:48 pm |
|
|
So i have had quite a big look for the information on hear, and i can seem to get a good answer...
I currently have 29" tyres on my car with standard gears. Currently when going up a hill, 2nd low hates it and i have to end up doing up in 1st...
These hills i can cruise up in 3rd low in my dads 100s landcrusier (which im used to)
I am looking at putting 31" tyres on my vit. And was wondering what are the best gears for this?? Its still going to be a daily driver at this point in time. But i need better gears for off road
any advise about what gears (6.5, 4.25?, anything) and or a website to buy these off will help hugely
Cheers,
Sam
|
|
|
|
 |
buzbox
Joined: Thu Jul 16, 2009 11:30 pm Posts: 3600 Location: Wollongong NSW
Vehicle: LWB Sierra & XL7
|
 Posted: Wed Aug 15, 2012 3:11 pm |
|
|
Just put it in 1st gear. If you were to put in reduction gears just for that purpose, you'd probably do the same hill in 4th gear.
I'd only put reduction gears if I was doing alot of rock crawling. Even with 30's mine climbed a long decent gradiant just fine in 1st and I was towing a trailer. Even at the rock garden at Yalwal, 1st low on 31's did it ok.
just remember zooks are different to landcruisers. what size engine is in the cruiser? deisil? And what's a Vitara... In my opinion, Sure they're awsome to have, but it's a bit too much $$ for little gain. Especially for the terrain that you drive.
|
|
|
|
 |
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
 Posted: Wed Aug 15, 2012 3:22 pm |
|
|
Im not really looking for the hills, that i can keep doing in 1st
Its that low first will stall on itself very easy ... The crusier is a 4.2L diesel, and i KNOW it is a different car and has alot better engine braking,
I was looking for low gears for rock crawling and really technical stuff, i find myself on the breaks to much on certain parts, its either im on the breaks, or full on the accelorator
|
|
|
|
 |
lee88
Joined: Sun May 09, 2010 2:10 pm Posts: 87 Location: Perth
|
 Posted: Wed Aug 15, 2012 3:54 pm |
|
|
I disagree - i think its a huge gain if you only do harder rock driving. the low range gears make it so much more controlled and driveable on rocks & steep descents. (On anything other than rocks though, low range will practically become useless.) I haven't driven much yet though as my car has been off the road for a while, but with the few times i've taken it out with the crawler gears the difference is amazing on rocks but it is VERY slow with 31s. (Eg. if i put it in first gear low range i can hop out and walk faster then the car drives..)
I suggest think about what you want from you car and what you use it for before you spend the money on the gearing. And lowrangeoffroad and trailtough in the US sell the gears.
|
|
|
|
 |
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
 Posted: Wed Aug 15, 2012 4:06 pm |
|
lee88 wrote: I disagree - i think its a huge gain if you only do harder rock driving. the low range gears make it so much more controlled and driveable on rocks & steep descents. (On anything other than rocks though, low range will practically become useless.) I haven't driven much yet though as my car has been off the road for a while, but with the few times i've taken it out with the crawler gears the difference is amazing on rocks but it is VERY slow with 31s. (Eg. if i put it in first gear low range i can hop out and walk faster then the car drives..)
I suggest think about what you want from you car and what you use it for before you spend the money on the gearing. And lowrangeoffroad and trailtough in the US sell the gears. With my dads car, in 1st his foot is always on the accelorator, thats how slow it is, which is better AND safer then breaking down a hill.... In the end im putting a 3" calmini kit and a 3" body lift with 33's... but for now it will be 2" body and lift with 31's
|
|
|
|
 |
Gwagensteve
Joined: Thu Feb 26, 2009 10:30 pm Posts: 12997 Location: Melbourne
|
 Posted: Wed Aug 15, 2012 6:29 pm |
|
|
You're not comparing apples with apples. Land cruisers have lower gearing but also a completely different engine characteristic.
If you want more gearing off road fit transfer gears (there's only one ratio available. It's plenty low enough for crawling.
31's and especially 33"s will suck on road regardless of the transfer gears as they only effect low range.
Steve.
|
|
|
|
 |
atari4x4

az supporter
Joined: Mon Dec 11, 2006 10:30 pm Posts: 34843 Location: East Radelayed
Vehicle: SV420+SV620 Vitara's
|
 Posted: Wed Aug 15, 2012 6:36 pm |
|
Samwich wrote: In the end im putting a 3" calmini kit and a 3" body lift with 33's... but for now it will be 2" body and lift with 31's you must have money to burn, why go for the step in between... it just makes no sense to me. as steve said high range is going to be bad on either tyre.
_________________ You're just hating because you don't understand
|
|
|
|
 |
buzbox
Joined: Thu Jul 16, 2009 11:30 pm Posts: 3600 Location: Wollongong NSW
Vehicle: LWB Sierra & XL7
|
 Posted: Wed Aug 15, 2012 8:03 pm |
|
lee88 wrote: I disagree - i think its a huge gain if you only do harder rock driving.
That is pretty much what I was getting at. Sam after explaining to me what you mainly want to use it for and which direction you should go with it, I think it's waay overkill. I think you should try driving those types of terrain then making your mind up. That's pretty much what I did and come to the conclusion of that I don't need transfer gears. With a locked rear end I definitly noticed I was going much slower over stuff like rocks and hill climbs. You've just installed a new 2" sus lift with new tyres, One week later you want to change that to 6" lift, bigger tyres, transfer gears, blah blah blah. Now I read you want a sierra?? I think you need to think hard about what you really want, a Landcruiser.
|
|
|
|
 |
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
 Posted: Thu Aug 16, 2012 10:21 am |
|
atari4x4 wrote: Samwich wrote: In the end im putting a 3" calmini kit and a 3" body lift with 33's... but for now it will be 2" body and lift with 31's you must have money to burn, why go for the step in between... it just makes no sense to me. as steve said high range is going to be bad on either tyre. Im a 19yo that works in the public service... i have ALOT of money to burn hahaha 
|
|
|
|
 |
tanshi

az supporter
Joined: Tue Jan 09, 2007 10:30 pm Posts: 7719 Location: Brisbane
|
 Posted: Thu Aug 16, 2012 10:32 am |
|
|
33s on a vitara is gonna mean exploding CVs!!!!
to me it sounds like your building the wrong car for the purpose.
|
|
|
|
 |
atari4x4

az supporter
Joined: Mon Dec 11, 2006 10:30 pm Posts: 34843 Location: East Radelayed
Vehicle: SV420+SV620 Vitara's
|
 Posted: Thu Aug 16, 2012 10:32 am |
|
why bother messing around with baby steps... man up & go 33's straight up. 
_________________ You're just hating because you don't understand
|
|
|
|
 |
abclarke
Joined: Mon Feb 14, 2011 8:19 am Posts: 1966 Location: Couridjah
Vehicle: 1985 Holden Drover
|
 Posted: Thu Aug 16, 2012 10:34 am |
|
Samwich wrote: atari4x4 wrote: Samwich wrote: In the end im putting a 3" calmini kit and a 3" body lift with 33's... but for now it will be 2" body and lift with 31's you must have money to burn, why go for the step in between... it just makes no sense to me. as steve said high range is going to be bad on either tyre. Im a 19yo that works in the public service... i have ALOT of money to burn hahaha  Haha that's our tax money being well spent then I see? 
|
|
|
|
 |
buzbox
Joined: Thu Jul 16, 2009 11:30 pm Posts: 3600 Location: Wollongong NSW
Vehicle: LWB Sierra & XL7
|
 Posted: Thu Aug 16, 2012 10:46 am |
|
Samwich wrote: atari4x4 wrote: Samwich wrote: In the end im putting a 3" calmini kit and a 3" body lift with 33's... but for now it will be 2" body and lift with 31's you must have money to burn, why go for the step in between... it just makes no sense to me. as steve said high range is going to be bad on either tyre. Im a 19yo that works in the public service... i have ALOT of money to burn hahaha  Too much money, not enough sense. If I were you I'd look at putting some of those earnings into a home saver account and or investment properties. I would've fkn killed to own my own home by the age of 25. I know you don't really think about that shit when your young, but give it 5-10 years and you'd be saying shoulda coulda woulda but didn't. But... oh well.. As you were.....................
|
|
|
|
 |
atari4x4

az supporter
Joined: Mon Dec 11, 2006 10:30 pm Posts: 34843 Location: East Radelayed
Vehicle: SV420+SV620 Vitara's
|
 Posted: Thu Aug 16, 2012 10:55 am |
|
lol i dont think he signed up for financial advice 
_________________ You're just hating because you don't understand
|
|
|
|
 |
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
 Posted: Thu Aug 16, 2012 10:59 am |
|
buzbox wrote: Samwich wrote: atari4x4 wrote: Samwich wrote: In the end im putting a 3" calmini kit and a 3" body lift with 33's... but for now it will be 2" body and lift with 31's you must have money to burn, why go for the step in between... it just makes no sense to me. as steve said high range is going to be bad on either tyre. Im a 19yo that works in the public service... i have ALOT of money to burn hahaha  Too much money, not enough sense. If I were you I'd look at putting some of those earnings into a home saver account and or investment properties. I would've fkn killed to own my own home by the age of 25. I know you don't really think about that shit when your young, but give it 5-10 years and you'd be saying shoulda coulda woulda but didn't. But... oh well.. As you were..................... Haha yeah i got 60k ish away atm... and i put a % of my pay away, still have quite abit to play around with 
|
|
|
|
 |
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
 Posted: Thu Aug 16, 2012 11:00 am |
|
abclarke wrote: Samwich wrote: atari4x4 wrote: Samwich wrote: In the end im putting a 3" calmini kit and a 3" body lift with 33's... but for now it will be 2" body and lift with 31's you must have money to burn, why go for the step in between... it just makes no sense to me. as steve said high range is going to be bad on either tyre. Im a 19yo that works in the public service... i have ALOT of money to burn hahaha  Haha that's our tax money being well spent then I see?  HAHAHA yeah well at least im not as bad as the AFP....
|
|
|
|
 |
atari4x4

az supporter
Joined: Mon Dec 11, 2006 10:30 pm Posts: 34843 Location: East Radelayed
Vehicle: SV420+SV620 Vitara's
|
 Posted: Thu Aug 16, 2012 11:06 am |
|
60k in the bank, i'd be lucky to have 60c in mine... 19yo & that sort of money, i'm guessing "public service" means your a drug dealer? FYI stashed cash money is where it's at. 
_________________ You're just hating because you don't understand
|
|
|
|
 |
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
 Posted: Thu Aug 16, 2012 11:24 am |
|
Ive been working since 13 haha and have Saved ever since Been in the public service for near 2 years now (since i finished college) 
|
|
|
|
 |
tombutt
Joined: Sat Jul 19, 2008 11:30 pm Posts: 1917 Location: brisbane
|
 Posted: Fri Aug 17, 2012 1:39 pm |
|
|
gears are good but unless your doing really slow work annoying at times low range almost becomes unusable for anything that isn't slow speed crawling work if your in the mud you will be in the higher end of the gear box if your just trying to cruise along you will be high range. i go out with a lot of hilux's cruiser's and the alike and where they will be in low range cruising around between things i always have to stop and go to high range just make sure your not gearing it too low for the driving your doing
|
|
|
|
 |
DarkHorse

az supporter
Joined: Wed Apr 14, 2010 11:30 pm Posts: 5413
Vehicle: 08 SV650
|
 Posted: Sat Aug 18, 2012 5:45 pm |
|
Gearing too low... get bigger tyres 
|
|
|
|
 |
shandy92

az supporter
Joined: Tue Nov 25, 2008 10:30 pm Posts: 5066 Location: perth, Australia
|
 Posted: Sun Aug 19, 2012 7:31 pm |
|
DarkHorse wrote: Gearing too low... get bigger tyres  ahah just thinking the same thing....i just bought a set of gears and getting them fitted at the moment, there is no other cheap option availible for the vits so the choice was rather easy. if i could think of a way to easily run a sierra case and get it engineered i would do that but i cant.
|
|
|
|
 |
|