auszookers.com • View topic - DIY LED RoCk LiGhTs

Board index » Talking About Stuff » I made it and fabrication

DIY LED RoCk LiGhTs

Page 1 of 2

[ 50 posts ]

Go to page 1, 2 Next

Print view

Previous topic | Next topic

Author

Message

atari4x4

az supporter

Joined: Mon Dec 11, 2006 10:30 pm
Posts: 34843
Location: East Radelayed
Vehicle: SV420+SV620 Vitara's

Posted: Fri Mar 25, 2011 11:15 am

I grabbed a 5m roll of SMD LED's, waterproof to IP65 with 120 LEDs per meter off ebay, some clear bong tubing & condute saddles from Bunnings, wire, silicone, terminals etc I already had.

Measure twice cut once...

Measure & cut LED strip to length & cut a length of tubing a bit longer. The LED's can be cut down in groups of 3.

Tape a piece of wire to the end of the LED strip & start feeding it into the bong tubing. Be gentle when pulling on the strip...

Trim back the silicone to reveal the solder tabs & solder on your wires.

At this stage I test to see if it works...

Wrap a few turns of tape around the soldered end to make a bit of a bung to stop the silicone spreading. Now pull the feed wire so the LED strip is poking out the end, un tape it & GENTLY pull the power wire end back so the LED strip is just inside the open end & feed a dob or 2 of silicone in the end to seal it.

With the power end I pumped a bit of silicone in til it fills up.

Let silicone to cure overnight... :wink:

I then made a set of "caps" out of irrigation poly pipe by sliding it over the bong tubing & filling them up with silicone.

Mount them where ever you can fit them, wire them up using a relay & fuse... and marvel at the extra layer of rice added to you 4wd, now just get some NOS seat covers & some blue valve caps & the Hot4's crew will be envious.

_________________
You're just hating because you don't understand

monley

az supporter

Joined: Wed Nov 24, 2010 7:58 am
Posts: 11092
Location: Mandurah.W.A.
Vehicle: 84 LWB NT

Posted: Fri Mar 25, 2011 11:21 am

Nice job!

And fark they are bright.

_________________
Tell my arse, he actually gives a crap!

Rusho

Tubby Elfsdong

Joined: Sun Aug 02, 2009 11:30 pm
Posts: 6501
Location: Northside, Brisbane
Vehicle: Coily Sierra

Posted: Fri Mar 25, 2011 11:22 am

Gus....it was a bit late for the Madi Gra though isn't it :finger:

_________________
Shep is a closet jimny lover!!!!

atari4x4

az supporter

Joined: Mon Dec 11, 2006 10:30 pm
Posts: 34843
Location: East Radelayed
Vehicle: SV420+SV620 Vitara's

Posted: Fri Mar 25, 2011 11:24 am

monkey wrote:

Nice job!

And fark they are bright.

that is a long exposure.... but yeah they're bright enough!

_________________
You're just hating because you don't understand

atari4x4

az supporter

Joined: Mon Dec 11, 2006 10:30 pm
Posts: 34843
Location: East Radelayed
Vehicle: SV420+SV620 Vitara's

Posted: Fri Mar 25, 2011 11:27 am

Rusho wrote:

:goodjob: Gus....it was a bit late for the Madi Gra though isn't it :finger:

I'm preparing for next years.... you do know I'm towing you're coily as the float. DM90 and you are the King & Queen, you can decide who's going to be who. :lol:

_________________
You're just hating because you don't understand

Rusho

Tubby Elfsdong

Joined: Sun Aug 02, 2009 11:30 pm
Posts: 6501
Location: Northside, Brisbane
Vehicle: Coily Sierra

Posted: Fri Mar 25, 2011 11:30 am

atari4x4 wrote:

Rusho wrote:

:goodjob: Gus....it was a bit late for the Madi Gra though isn't it :finger:

I'm preparing for next years.... you do know I'm towing you're coily as the float. DM90 and you are the King & Queen, you can decide who's going to be who. :lol:

We can both be Queens pompoms

_________________
Shep is a closet jimny lover!!!!

zookyute1981

Joined: Sat Jun 27, 2009 11:30 pm
Posts: 314
Location: mount barker (GSWA)

Posted: Fri Mar 25, 2011 12:52 pm

great idea mate will give it a go wth me camper trailer

steak_knife

az supporter

Joined: Fri May 22, 2009 11:30 pm
Posts: 21335
Location: Smart Ass Island

Posted: Fri Mar 25, 2011 6:33 pm

You forgot the link to the light's so we all can copy you..

_________________
I used to be indecisive,
now I'm not so sure.....

royce

omnipotent being

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 17216
Location: Pluto

Posted: Fri Mar 25, 2011 7:25 pm

can you get a pic of a 3 led piece lit up?

bluzooker89

az supporter

Joined: Sun Mar 14, 2010 10:30 pm
Posts: 89
Location: western australia

Posted: Fri Mar 25, 2011 8:13 pm

Awsum job mate will be doin sumthing similiar on mine

_________________
built not bought

hutch

az supporter

Joined: Sun Nov 30, 2008 10:30 pm
Posts: 1214
Location: SW Bris

Posted: Fri Mar 25, 2011 8:17 pm

thats a good build there.
What did it cost all up?

_________________
255 characters

SuziBlu

Joined: Mon Sep 14, 2009 11:30 pm
Posts: 4268
Location: Eyre Peninsula

Posted: Fri Mar 25, 2011 8:29 pm

steak_knife wrote:

:helloo:
You forgot the link to the light's so we all can copy you..

Had a bit of bong hose left over, had to use it, an forgot. kewllll

_________________
Bad decisions make good stories.

abclarke

Joined: Mon Feb 14, 2011 8:19 am
Posts: 1966
Location: Couridjah
Vehicle: 1985 Holden Drover

Posted: Fri Mar 25, 2011 9:37 pm

Looks mad mate! Looks simple enough too

_________________
1989 WT Sierra.

tim80z

az supporter

Joined: Tue Dec 14, 2010 8:09 pm
Posts: 722
Location: Parkes NSW
Vehicle: 2006 Jimny - SOLD

Posted: Fri Mar 25, 2011 9:43 pm

http://cgi.ebay.com.au/600LED-3528-SMD-White-5M-Flexible-Strip-Lamp-Light-Car-/220744184101?pt=AU_Car_Parts_Accessories&hash=item336560f125

Is that the LED strip you used?

- Tim.

_________________
SOLD - 2006 Jimny M18A, NSW Engineered

SuziBlu

Joined: Mon Sep 14, 2009 11:30 pm
Posts: 4268
Location: Eyre Peninsula

Posted: Fri Mar 25, 2011 10:22 pm

tim80z wrote:

http://cgi.ebay.com.au/600LED-3528-SMD-White-5M-Flexible-Strip-Lamp-Light-Car-/220744184101?pt=AU_Car_Parts_Accessories&hash=item336560f125

Is that the LED strip you used?

- Tim.

Bloody hell, 14-24 working days airfreight to oz.

_________________
Bad decisions make good stories.

Chop

az supporter

Joined: Sat Aug 12, 2006 11:30 pm
Posts: 6456
Location: Radelaide ofcourse!
Vehicle: Suzuki GV 03/ 2010 DDIS NGV

Posted: Fri Mar 25, 2011 10:31 pm

tim80z wrote:

http://cgi.ebay.com.au/600LED-3528-SMD-White-5M-Flexible-Strip-Lamp-Light-Car-/220744184101?pt=AU_Car_Parts_Accessories&hash=item336560f125

Is that the LED strip you used?

- Tim.

I'd be more inclined to get the 300 led 5m job they seem to be bigger led's, also that one you put up aint waterproof.

_________________
Chop

Suzuki's are like Mogwai's, they multiply!

Last edited by Chop on Fri Mar 25, 2011 10:40 pm, edited 1 time in total.

shandy92

az supporter

Joined: Tue Nov 25, 2008 10:30 pm
Posts: 5066
Location: perth, Australia

Posted: Fri Mar 25, 2011 10:33 pm

Chop wrote:

tim80z wrote:

http://cgi.ebay.com.au/600LED-3528-SMD-White-5M-Flexible-Strip-Lamp-Light-Car-/220744184101?pt=AU_Car_Parts_Accessories&hash=item336560f125

Is that the LED strip you used?

- Tim.

I'd be more inclined to get the 300 led 5m job they seem to be bigger led's, also that one i you put up aint waterproof.

i thought that was why he put them inside the bong tube??

Chop

az supporter

Joined: Sat Aug 12, 2006 11:30 pm
Posts: 6456
Location: Radelaide ofcourse!
Vehicle: Suzuki GV 03/ 2010 DDIS NGV

Posted: Fri Mar 25, 2011 10:44 pm

Maybe, I'd say its more for protection under the car and the fact you cant use the sticky back to stick to a chassis :wink:

If you buy the waterproof stuff you can use it elsewhere and just stick it without putting it in tube.

_________________
Chop

Suzuki's are like Mogwai's, they multiply!

SuziBlu

Joined: Mon Sep 14, 2009 11:30 pm
Posts: 4268
Location: Eyre Peninsula

Posted: Fri Mar 25, 2011 10:45 pm

shandy92 wrote:

Chop wrote:

tim80z wrote:

http://cgi.ebay.com.au/600LED-3528-SMD-White-5M-Flexible-Strip-Lamp-Light-Car-/220744184101?pt=AU_Car_Parts_Accessories&hash=item336560f125

Is that the LED strip you used?

- Tim.

I'd be more inclined to get the 300 led 5m job they seem to be bigger led's, also that one i you put up aint waterproof.

i thought that was why he put them inside the bong tube??

Shhh, I think chop had a hard night, he isn't fully awake yet, still on his first cuppa. :lol:

_________________
Bad decisions make good stories.

atari4x4

az supporter

Joined: Mon Dec 11, 2006 10:30 pm
Posts: 34843
Location: East Radelayed
Vehicle: SV420+SV620 Vitara's

Posted: Sat Mar 26, 2011 1:51 am

The bong tubing is for an extra layer of protection from mud, rocks & crap not to waterproof the LED's... plus now I'll never have to cut down my garden hose again.

I bought the smaller LED's by mistake, I just saw the 120 per meter & went buy now. The larger ones would have been better & mega bright, the small ones would make awesome interior lights, camper lights, lights in rear storage units.

Cost = ummm about $80-90 depends on how well stocked the workshop is, LED's were $60, $8 for the tubing, $4 for the condute saddles... the other stuff I had already, wire, solder, tape, silicone, cable ties etc.

I've got a few little left overs, I'll wire them up & try to get some photo's.

_________________
You're just hating because you don't understand

Chop

az supporter

Joined: Sat Aug 12, 2006 11:30 pm
Posts: 6456
Location: Radelaide ofcourse!
Vehicle: Suzuki GV 03/ 2010 DDIS NGV

Posted: Sat Mar 26, 2011 2:50 am

Nice

_________________
Chop

Suzuki's are like Mogwai's, they multiply!

89_tintop

az supporter

Joined: Fri Aug 07, 2009 11:30 pm
Posts: 3159
Location: gold coast

Posted: Sat Mar 26, 2011 4:00 am

nice job...

just added another thing to he list of stuff to do.

to really rice it up.. make em come on when you open the door.

_________________
http://auszookers.com/index.php?name=Forums&file=v

vl2dy4

az supporter

Joined: Wed Feb 16, 2011 8:40 am
Posts: 424
Location: Australind WA

Posted: Sat Mar 26, 2011 12:24 pm

Awesome DIY mate i will def add this to my zook for night wheeling. Would the larger LEDS be better?

Brighter is always better.

Cheers
Conrad

_________________
I HATE CYCLISTS!!!

larry

Joined: Wed Sep 08, 2010 3:15 am
Posts: 657
Location: penrith, NSW

Posted: Sun Mar 27, 2011 9:17 am

rice job mate

larry

Joined: Wed Sep 08, 2010 3:15 am
Posts: 657
Location: penrith, NSW

Posted: Sun Mar 27, 2011 9:17 am

nice*

dm90

Joined: Sun Nov 29, 2009 10:30 pm
Posts: 4349
Location: Perth

Posted: Sun Mar 27, 2011 1:18 pm

Rusho wrote:

atari4x4 wrote:

Rusho wrote:

:goodjob: Gus....it was a bit late for the Madi Gra though isn't it :finger:

I'm preparing for next years.... you do know I'm towing you're coily as the float. DM90 and you are the King & Queen, you can decide who's going to be who. :lol:

We can both be Queens pompoms

nice job there mate,

i will do something similar also

atari4x4

az supporter

Joined: Mon Dec 11, 2006 10:30 pm
Posts: 34843
Location: East Radelayed
Vehicle: SV420+SV620 Vitara's

Posted: Tue Mar 29, 2011 1:39 am

3 led's = 25mm

looking in down next to the battery

in the washer bottle :crazy:

random hole in bonnet

about a foot off the ground

_________________
You're just hating because you don't understand

royce

omnipotent being

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 17216
Location: Pluto

Posted: Tue Mar 29, 2011 2:14 am

abclarke

Joined: Mon Feb 14, 2011 8:19 am
Posts: 1966
Location: Couridjah
Vehicle: 1985 Holden Drover

Posted: Tue Mar 29, 2011 4:21 am

They look pretty well powered for the smaller ones! DO WANT!

_________________
1989 WT Sierra.

lyallrichards

Joined: Thu Dec 30, 2010 12:48 pm
Posts: 198
Location: kingsley perth wa
Vehicle: 91 sierra

Posted: Tue Mar 29, 2011 5:53 am

love the idea of putting them in a tube, i didn't think of that when i did mine

doing them off the door is pretty easy going, i put those ones you have on the roll bar of my suzi and wired them plus another strip attached to door itself for door to come on when the door does.

under mine i used hard plastic 3 colour strip leds of 30cm long, glued to a plastic u channel,

they also turn white but i havn't got a pic of them white atm

this one you can kinda see the leds on the roll bar

how long have you been running your in that tube, cause mine heat up alot and i was wondering how your coped inside that sealed tube??

_________________
K.I.T
Knight rider
d(^_^)b

Page 1 of 2

[ 50 posts ]

Go to page 1, 2 Next

Board index » Talking About Stuff » I made it and fabrication

Who is online

Users browsing this forum: No registered users and 4 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum