auszookers.com • View topic - got myself a pipe bender !

Board index » Talking About Stuff » I made it and fabrication

got myself a pipe bender !

Page 1 of 1

[ 17 posts ]

Print view

Previous topic | Next topic

Author

Message

steve

I live here!

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 7681
Location: Brisbane
Vehicle: 75 Cruiser

Posted: Sat Nov 14, 2009 8:55 pm

well finally i have got myself a pipe bender, and did my first job with it today....

new cistern and plumbing :thefinger:

You do not have the required permissions to view the files attached to this post.

royce

omnipotent being

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 17216
Location: Pluto

Posted: Sat Nov 14, 2009 9:03 pm

are you going to polish that copper?

steak_knife

az supporter

Joined: Fri May 22, 2009 11:30 pm
Posts: 21335
Location: Smart Ass Island

Posted: Sat Nov 14, 2009 9:04 pm

That look's shit house steve :roll:

_________________
I used to be indecisive,
now I'm not so sure.....

royce

omnipotent being

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 17216
Location: Pluto

Posted: Sat Nov 14, 2009 9:20 pm

whats the half flush rating on that one?

steve

I live here!

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 7681
Location: Brisbane
Vehicle: 75 Cruiser

Posted: Sat Nov 14, 2009 9:20 pm

royce, yer maybe i should paint it with some clear coat.

royce

omnipotent being

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 17216
Location: Pluto

Posted: Sat Nov 14, 2009 9:23 pm

Hammer tone

atari4x4

az supporter

Joined: Mon Dec 11, 2006 10:30 pm
Posts: 34843
Location: East Radelayed
Vehicle: SV420+SV620 Vitara's

Posted: Sat Nov 14, 2009 10:00 pm

that looks like a shit job...

_________________
You're just hating because you don't understand

steve

I live here!

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 7681
Location: Brisbane
Vehicle: 75 Cruiser

Posted: Sat Nov 14, 2009 10:13 pm

hah yeah , bit of toilet humour there

Scrawny

I live here!

Joined: Tue Jan 29, 2008 10:30 pm
Posts: 10528
Location: Brissie
Vehicle: Popemobile

Posted: Sat Nov 14, 2009 10:20 pm

Bout time you replaced the old dunny!!

Damo

az supporter

Joined: Sat Jul 22, 2006 11:30 pm
Posts: 4661
Location: Brisbane

Posted: Sat Nov 14, 2009 11:14 pm

Shit of a job

_________________
SJ50.4.LYF

Saam

az supporter

Joined: Mon Jun 12, 2006 11:30 pm
Posts: 2068
Location: Sunshine Coast

Posted: Sat Nov 14, 2009 11:17 pm

i'd rather do a poo than install a toilet.. yeah.. hmm

andypandy

Joined: Tue Oct 20, 2009 10:30 pm
Posts: 16
Location: buderim

Posted: Sat Nov 14, 2009 11:28 pm

looks shit (pun intended)
but not bad for ur first go

_________________
I would engage you in a battle of wits, but I refu

andrewa

Joined: Fri Aug 25, 2006 11:30 pm
Posts: 278
Location: bundamba

Posted: Sun Nov 15, 2009 1:16 am

thats the shit steve. going into the freelance plumbing buisness are we steve. :goodjob:

brendan

Joined: Sun Jul 27, 2008 11:30 pm
Posts: 1484
Location: Sydney

Posted: Sun Nov 15, 2009 2:24 am

thats tube not pipe :roll:

could have use chrome plated copper and fittings, look better,

_________________
navara on 33s. hopfully rear air locker soon

just_cruizin

az supporter

Joined: Sun Jun 25, 2006 11:30 pm
Posts: 2867
Location: here

Posted: Sun Nov 15, 2009 6:02 am

Stainless braided hose always look bling.

Have you christen it yet with an AGB or some Indian.

_________________

greenzook89 wrote:

31zook wrote:

Makes me want something similar

MacDaddy

az supporter

Joined: Thu Mar 26, 2009 10:30 pm
Posts: 10453
Location: Perth, Australia
Vehicle: Jeep

Posted: Sun Nov 15, 2009 9:59 am

steve wrote:

well finally i have got myself a pipe bender, and did my first job with it today....

new cistern and plumbing :thefinger:

Hi Steve,

Seeing as i dont see any oxy torch marks on the copper, i dont think it was the spring type pipe bender, i am guessing its the two pully type benders that hold the pipe inside, and you pull on the two arms and the pipe bends without squashing flat... if you can understand that...

I used to be a Refrigeration Technician before i became a Comp Techie, so i used both types of copper tube benders quite often, he he... did you have the flaring tool as well ?

Cheers

steve

I live here!

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 7681
Location: Brisbane
Vehicle: 75 Cruiser

Posted: Sun Nov 15, 2009 11:53 am

just_cruizin wrote:

Stainless braided hose always look bling.

Have you christen it yet with an AGB or some Indian.

I was going to get the stainless braided hoses, but i think that would be a really bad idea to have in the toilet with regards to cleanliness.

No hasn't been completely tested yet.

Macbear, yeah it's a two arm bender. Don't need a flaring tool for these things, the olives (plastic ring) on the tube/pipe squish it when you tighten the nut.

Page 1 of 1

[ 17 posts ]

Board index » Talking About Stuff » I made it and fabrication

Who is online

Users browsing this forum: No registered users and 14 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum