auszookers.com • View topic

Board index » Talking About Stuff » I made it and fabrication

Machining fail

Page 1 of 1

[ 16 posts ]

Print view

Previous topic | Next topic

Author

Message

Damo

az supporter

Joined: Sat Jul 22, 2006 11:30 pm
Posts: 4661
Location: Brisbane

Posted: Sun Feb 14, 2010 12:50 pm

Note to self, tighten up lathe chuck properly :oops:

_________________
SJ50.4.LYF

royce

omnipotent being

Joined: Sun Jun 11, 2006 11:30 pm
Posts: 17216
Location: Pluto

Posted: Sun Feb 14, 2010 12:58 pm

That looks like it was going really well up to there

steak_knife

az supporter

Joined: Fri May 22, 2009 11:30 pm
Posts: 21335
Location: Smart Ass Island

Posted: Sun Feb 14, 2010 1:04 pm

royce wrote:

That looks like it was going really well up to there

First & last time that happened to me I shat!!

Just wondering why your making cone's for a bong tho..

_________________
I used to be indecisive,
now I'm not so sure.....

hutch

az supporter

Joined: Sun Nov 30, 2008 10:30 pm
Posts: 1214
Location: SW Bris

Posted: Sun Feb 14, 2010 1:20 pm

hmmm.... scissors? blue box?.... interested lathe

_________________
255 characters

Damo

az supporter

Joined: Sat Jul 22, 2006 11:30 pm
Posts: 4661
Location: Brisbane

Posted: Sun Feb 14, 2010 1:36 pm

No need to be so impressed Royce, they are cnc machined pieces and i am just making them a bit smaller so they fit in a zook manifold

_________________
SJ50.4.LYF

ball

I live here!

Joined: Wed Oct 22, 2008 10:30 pm
Posts: 4673
Location: Katherine

Posted: Sun Feb 14, 2010 2:17 pm

Were you holding on to the threaded part ?

TZAR

az supporter

Joined: Tue Aug 01, 2006 11:30 pm
Posts: 3459
Location: licking some windows
Vehicle: LJ20 LJ50

Posted: Sun Feb 14, 2010 4:23 pm

http://www.youtube.com/watch?v=uWOAAyN3btc

_________________
Camels have nice toes

Damo

az supporter

Joined: Sat Jul 22, 2006 11:30 pm
Posts: 4661
Location: Brisbane

Posted: Sun Feb 14, 2010 6:44 pm

ball wrote:

Were you holding on to the threaded part ?

There is a shoulder above the threaded section, I had it holding that.

It worked great for the other three, I just forgot to nip up the chuck for this one. It was a reminder of how you have to concentrate doing this stuff. It could have been a lot worse!

Hey Joe!!?!?!

_________________
SJ50.4.LYF

Joe

I live here!

Joined: Sat Jul 04, 2009 11:30 pm
Posts: 49041
Location: Rockingham W.A
Vehicle: JB74

Posted: Sun Feb 14, 2010 7:45 pm

Oh bugger at least ya not hurt mate

and stekkys right it does look like a cone piece :lol:

_________________
Joe likes boobs ( . )( . ) ( ° )( ° )

Joe

I live here!

Joined: Sat Jul 04, 2009 11:30 pm
Posts: 49041
Location: Rockingham W.A
Vehicle: JB74

Posted: Sun Feb 14, 2010 7:49 pm

TZAR wrote:

http://www.youtube.com/watch?v=uWOAAyN3btc

_________________
Joe likes boobs ( . )( . ) ( ° )( ° )

joeblow

Joined: Sat May 10, 2008 11:30 pm
Posts: 3273
Location: melbourne

Posted: Sun Feb 14, 2010 8:10 pm

Damo wrote:

Hey Joe!!?!?!

haha.....bits flying out of a lathe i can deal with.......

placing my noggin in one is another story. :wink:

_________________
builder of custom road legal zooks......and stuff.

JrZook

Joined: Tue Aug 08, 2006 11:30 pm
Posts: 5517
Location: Holland Park
Vehicle: Awesome!!

Posted: Sun Feb 14, 2010 11:05 pm

Bah whats wrong with that? Just bash the injector into it, nice inference fit and epoxy it into the mani. Think your just getting too picky :wink:

Fatzook

az supporter

Joined: Sat Oct 27, 2007 11:30 pm
Posts: 14977
Location: The Hills
Vehicle: Vitara, NGV

Posted: Sun Feb 14, 2010 11:30 pm

nice

Break any tooling?

Did you end up getting the measurements of the shaft for the crank handle?

_________________
2013 GV
1998 SV420 ute

steak_knife

az supporter

Joined: Fri May 22, 2009 11:30 pm
Posts: 21335
Location: Smart Ass Island

Posted: Mon Feb 15, 2010 1:37 am

joseph wrote:

TZAR wrote:

http://www.youtube.com/watch?v=uWOAAyN3btc

One wrong measurement. :lol:

_________________
I used to be indecisive,
now I'm not so sure.....

ball

I live here!

Joined: Wed Oct 22, 2008 10:30 pm
Posts: 4673
Location: Katherine

Posted: Mon Feb 15, 2010 2:00 am

Not measurement but a Z0 in the wrong spot in the program.

Damo

az supporter

Joined: Sat Jul 22, 2006 11:30 pm
Posts: 4661
Location: Brisbane

Posted: Wed Feb 17, 2010 1:51 pm

Fatzook wrote:

nice

Break any tooling?

Did you end up getting the measurements of the shaft for the crank handle?

Didn't break any tooling thankfully. It was just a cheapo carbide insert, but it survived.

I'll email you re: the crank handle shaft.

_________________
SJ50.4.LYF

Page 1 of 1

[ 16 posts ]

Board index » Talking About Stuff » I made it and fabrication

Who is online

Users browsing this forum: No registered users and 2 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum