[shep]

Is there a guide any where for fitting transfer gears to a vvt jimny push button transfer?

[atari4x4]

not sure, maybe suss out bigjimny?

[shep]

Haha their search is harder to drive then AZ's

[shep]

Can a vit 1.6 efi auto transfer case be bolted to a vit 1.6 efi 5 speed box?

[Joe]

shep wrote:

Can a vit 1.6 efi auto transfer case be bolted to a vit 1.6 efi 5 speed box?

Yes

[shandy92]

hi all,

i remember someone adding bracing to the front edge of an arb bar recovery point, as in welding plates to both sides of the bar to "increase the surface area". I remember them talking about welding upside down and being there first attempt at welding, but searching with those key words brings nothing.

pretty sure it was in a build thread, and the vitara (se416) was white!

thank you search gods!

[atari4x4]

Chop did it on Burnt Wood's ARB Bar, but I remember someone else doing it too.
viewtopic.php?f=4&t=11387&hilit=burnt+wood&start=420

[shandy92]

cheers, yeah not the one i was thinking of but thanks anyway.

[atari4x4]

i've been searching, but can't find the other one... i know the one you're talking about.

[atari4x4]

viewtopic.php?f=5&t=18209&hilit=ARB+recovery+point+weld&start=30

[shandy92]

your a legend Gus, not sure how you managed to find it with those keywords (ARB, recovery point, weld) did you do anything between them or just a space?

THANK YOU!!!!

[atari4x4]

a master never reveals his secrets, but i'm pretty sure Grimbo added a user name to the search to narrow down the results

aka mircowire

[Bludger]

err, not sure if it's the right place.....


how do i automatically subscribe to a thread as soon as i post in one.....

or must I subscribe manually?

[steve]

Bludger wrote:

err, not sure if it's the right place.....


how do i automatically subscribe to a thread as soon as i post in one.....

or must I subscribe manually?

I'm not sure if this is right, but you can try: http://www.auszookers.com/forum/ucp.php?i=prefs&mode=post

or see "User Control Panel / Board Preferences"

[Bludger]

steve wrote:

Bludger wrote:

err, not sure if it's the right place.....


how do i automatically subscribe to a thread as soon as i post in one.....

or must I subscribe manually?

I'm not sure if this is right, but you can try: http://www.auszookers.com/forum/ucp.php?i=prefs&mode=post

or see "User Control Panel / Board Preferences"

Thanks for the speedy reply.

Everything is on, will see how it goes....

[Samwich]

Where is the "Other rides/Car's" thread

looked up to 15 pages in the chat thread, and no luck on the search either :/

[Blkfxx]

Previous rides thread?

auszookers.com/forum/viewtopic.php?f=1&t=4857&hilit=other+rides

[DarkHorse]

Anyone know categorically what size the hard brake lines on an SV620 Vitara are?

Are the sizes an internal (bore) or external measurement? Calipers say 4.9mm external, so guessing 5mm? It's just off enough for me to worry that it might be 3/16" (4.75mm) internal, though I'm hoping Suzukisan didn't go imperial for one componant...

Anyone clarify?

[DarkHorse]

How often do the timing chains need doing on an H20A?

...and do we have a write-up for changing a clutch anywhere?

[jason_sgt]

How to program a new remote for an aftermarket alarm system...

I don't know the brand that is installed. The keyless fob / "doop doop" thing is busted. It has a fake walnut finish that has warn off, somewhat ruining the illusion of class that I work so hard to maintain.

so is there a thread on reprogramming or programming a new key?

[shandy92]

DarkHorse wrote:

How often do the timing chains need doing on an H20A?

...and do we have a write-up for changing a clutch anywhere?

Would think it would say in the manual, but usually 150 thou.
Dont think there is a clutch one.... Your turn:)

[DarkHorse]

Crap... :lol:

Mine doesn't actually need it yet, but was tempted by another one that looked mint but apparently needed clutch and had 118,000 on it. Seller not replying to SMS, voicemail or e-mail. :(

[atari4x4]

Darkhorse; Ninja has a good write up for the H series timing chains in his GV/XL-7 thread, it's pretty early on in the build stages... was a couple pdf's attached to a post from memory, has nice pretty colour pics n shit.

Jason; any idea on what kind of alarm... i can probably tell you how to reprogram a new remote into it, but probably not best to post a DIY guide on how to steal peoples cars.

[jason_sgt]

atari4x4 wrote:

Darkhorse; Ninja has a good write up for the H series timing chains in his GV/XL-7 thread, it's pretty early on in the build stages... was a couple pdf's attached to a post from memory, has nice pretty colour pics n shit.

Jason; any idea on what kind of alarm... i can probably tell you how to reprogram a new remote into it, but probably not best to post a DIY guide on how to steal peoples cars.

PM'd Thanks Gus.

[royce]

Anything about fitting Factory roof rails to a non roof railed Jimny?

[pete_79]

royce wrote:

Anything about fitting Factory roof rails to a non roof railed Jimny?

The guide that Scales did looks pretty good; http://auszookers.com/forum/viewtopic.php?f=17&t=35389

[greenzook89]

royce wrote:

Anything about fitting Factory roof rails to a non roof railed Jimny?

Skippy did it to his. Nutserts were used to attach the factory rails but he has since made a custom basket that includes the feet.

[royce]

Hows about power steer onto a non power steer one?

[Zoognoogle]

The secret to wiring carling switches for suzukis? Not sure about getting the lights to work properly, surely there's a thread on this??

[henno]

Lights are negatively switched. That's the most common mistake people make when wiring up lights.