specs on alloys?
| auszookers.com https://www.auszookers.com/forum/ |
|
| Wrecking G16B Vit - Last call, car scrapped tomorrow!!! https://www.auszookers.com/forum/viewtopic.php?f=7&t=37563 |
Page 1 of 4 |
| Author: | DarkHorse [ Wed Dec 05, 2012 6:11 pm ] |
| Post subject: | Wrecking G16B Vit - Last call, car scrapped tomorrow!!! |
Sad to say, but the Teflon Vitara is going to god. I'll be pulling all the aftermarket gear I can that will go straight across to the new SV620, so there'll be a bunch of gear off that as well. The major stuff is listed below, or hit me up for anything else and I'll let you know if I've got it available. Can get pics of anything, just ask. Car is getting picked up for scrap tomorrow morning, so anything not bought will be sent away with it. 1.6 LWB Stuff Almost new radiator - $100 Retro-fitted factory AC (all there, not cold - will include the J20 compressor) - $100 Body panels except tailgate, bonnet, rear bumper and front quarters - most good Interior mostly good, few screw holes in plastics Spare Radiator Hoses (top and outlet for G16B, top for G16A I think) - $20 [/list] 2.0L LWB stuff Control arms, springs, struts, shocks 4.8 (auto) rear diff centre - $50 Transfer Case (includes driveshafts for matching splines in early Vit) - $50 LHS CV shaft - $50 Other: J20 AC compressor (spins freely, unsure of working order) - $50 Winch fairlead - $FREE Pair of old Narva 170s (working fine) - $50 GV front brake rotors (brand new) - $100 |
|
| Author: | atari4x4 [ Wed Dec 05, 2012 6:16 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
specs on alloys?
|
|
| Author: | DarkHorse [ Wed Dec 05, 2012 6:20 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
No idea. Car is arriving in about half an hour, I'll get a tape measure onto them. |
|
| Author: | sideways [ Wed Dec 05, 2012 6:27 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
atari4x4 wrote: specs on alloys? X2, cool wheels.
|
|
| Author: | DarkHorse [ Wed Dec 05, 2012 6:45 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
Mullins Wheels 15x8, around +25 offset |
|
| Author: | alexxx [ Wed Dec 05, 2012 6:49 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
ill take the black XL7 ones!!!! |
|
| Author: | sideways [ Wed Dec 05, 2012 6:58 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
DarkHorse wrote: Keep that up, I might decide I like them better than the black XL7 ones...  Those are cool too though.
|
|
| Author: | ninjamoses [ Wed Dec 05, 2012 7:09 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
Alloys look decent. Need a build thread for the new one stat. Should be a monster in no time with everything you've got already. |
|
| Author: | DarkHorse [ Wed Dec 05, 2012 7:47 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
That's the plan. Got a trip late next week, so will at least be getting all the non-engineering stuff swapped by then. Build will come when I start building! CBF measuring rims tonight, sorry. |
|
| Author: | atari4x4 [ Wed Dec 05, 2012 7:52 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
thats cool, i'm guessing 16's? funny that the diff centres out of my blagon have ended up back in shitney.
|
|
| Author: | DarkHorse [ Wed Dec 05, 2012 7:56 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
Yeah, they'd have to be 16s, and assuming 7s given the relatively small tyres. Will confirm in the morning. Only thing funnier would be if someone from Brisbane or Perth bought them. |
|
| Author: | 93zook [ Wed Dec 05, 2012 7:57 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
feel like shipping the g16b interstate? |
|
| Author: | Oldmate28 [ Wed Dec 05, 2012 8:29 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
I'll take the cup holder console off ya! |
|
| Author: | camskea [ Wed Dec 05, 2012 9:01 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
Will the snorkel fit a SWB 1.6 carby motor? |
|
| Author: | DarkHorse [ Thu Dec 06, 2012 3:24 am ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
93zook wrote: feel like shipping the g16b interstate? Can do, I can strap it to a pallet and arrange a pickup time with the carrier of your choosing. Oldmate28 wrote: I'll take the cup holder console off ya! Done. PM me address and I'll get postage cost. camskea wrote: Will the snorkel fit a SWB 1.6 carby motor? I think so... what side does the air intake point? You might have to get tricky adapting some piping. |
|
| Author: | alexxx [ Thu Dec 06, 2012 5:45 am ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
You will have to adapt some piping but its an easy mod |
|
| Author: | DarkHorse [ Thu Dec 06, 2012 4:07 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
Bumping, list updated. |
|
| Author: | camskea [ Thu Dec 06, 2012 8:38 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
My intake runs over to the passenger side and out the wheel arch by the look of it... |
|
| Author: | DarkHorse [ Thu Dec 06, 2012 9:06 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
So just some convo tubing and a couple of hose clamps... Let me know if you want it. |
|
| Author: | monley [ Thu Dec 06, 2012 9:30 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
Willing to post the wheel spacers? If so, how much to 6210? |
|
| Author: | DarkHorse [ Thu Dec 06, 2012 10:02 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
Yeah mate, of course. AusPost website says around $25 postage. PM me an address and I'll give you bank details. |
|
| Author: | gvzookdriver [ Fri Dec 07, 2012 6:13 am ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
You making a trip to brissie any time soon |
|
| Author: | dono1 [ Fri Dec 07, 2012 8:38 am ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
How much for the 1.6 bonnet? Does it have the hinges attached? I need them too. Ill be keen in the body lift if the sale falls through. Cheers. Donny. |
|
| Author: | DarkHorse [ Fri Dec 07, 2012 8:44 am ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
gvzookdriver wrote: You making a trip to brissie any time soon Not on the immediate agenda. What you chasing? dono1 wrote: How much for the 1.6 bonnet? Does it have the hinges attached? I need them too. Ill be keen in the body lift if the sale falls through. Cheers. Donny. $100? Can have hinges. It has had some bracing underneath 'modified'... just so you know. |
|
| Author: | DarkHorse [ Fri Dec 07, 2012 8:54 am ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
atari4x4 wrote: specs on alloys? They're actually 15x8s, offset around +15  Going to hold onto them for the moment... Oh, and the car was originally owned in WA
|
|
| Author: | gvzookdriver [ Fri Dec 07, 2012 9:29 am ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
DarkHorse wrote: gvzookdriver wrote: You making a trip to brissie any time soon Not on the immediate agenda. What you chasing?. the hand winch. Need something just incase I get in trouble. (need to save up for a winch and bar to suit but lots of things needed before then) |
|
| Author: | DarkHorse [ Fri Dec 07, 2012 9:41 am ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
Yeah, it weighs about 25kg and will box up at 85x45x20 if you want to chase quotes. |
|
| Author: | gvzookdriver [ Fri Dec 07, 2012 10:10 am ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
What's your postcode |
|
| Author: | MADMANx511 [ Fri Dec 07, 2012 10:45 am ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
Centre console? Either one, looks to be the same in the 2.0 as my 1.6 so whichever is easiest for you. I'd need to pay for shipping to Brisbane 4053. |
|
| Author: | DarkHorse [ Fri Dec 07, 2012 1:00 pm ] |
| Post subject: | Re: Wrecking 1.6 and 2.0L LWB Vits |
MADMANx511 wrote: Centre console? Either one, looks to be the same in the 2.0 as my 1.6 so whichever is easiest for you. I'd need to pay for shipping to Brisbane 4053. Which bit? Handbrake surround, gearstick surround or stereo surrounds? Handbrake surround is pending, gearstick surround is a bit rough having been chopped for body lift and UHF face:  Boot is custom leather and glued to the underside. I'll include the matching transfer shift boot which is attached to the surround that screws down to the body. $15 shipped. Stereo surround pieces should be fine, $15 shipped. |
|
| Page 1 of 4 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|