| auszookers.com https://www.auszookers.com/forum/ |
|
| remove https://www.auszookers.com/forum/viewtopic.php?f=7&t=34607 |
Page 1 of 1 |
| Author: | RIKSTR [ Tue Jul 31, 2012 10:07 am ] |
| Post subject: | remove |
|
|
|
| Author: | RIKSTR [ Thu Aug 02, 2012 7:54 pm ] |
| Post subject: | Re: [ACT] XL7 4.24:1 Reduction Gears |
To the top |
|
| Author: | RIKSTR [ Tue Aug 07, 2012 8:54 am ] |
| Post subject: | Re: [ACT] XL7 4.24:1 Reduction Gears |
This may fit GV autos as well, all depends on the rear output shaft |
|
| Author: | RIKSTR [ Wed Aug 15, 2012 5:56 am ] |
| Post subject: | Re: [ACT] XL7 4.24:1 Reduction Gears |
once in a lifetime opportunity |
|
| Author: | RIKSTR [ Mon Aug 27, 2012 6:15 am ] |
| Post subject: | Re: [ACT] XL7 4.24:1 Reduction Gears |
Still here |
|
| Author: | RIKSTR [ Thu Sep 06, 2012 11:32 am ] |
| Post subject: | Re: [ACT] XL7 4.24:1 Reduction Gears |
Still here, make and offer if you want 'em |
|
| Author: | thesupervisor [ Thu Sep 06, 2012 1:13 pm ] |
| Post subject: | Re: [ACT] XL7 4.24:1 Reduction Gears |
if they fit my 99 gv auto id go $500 posted |
|
| Author: | RIKSTR [ Wed Sep 19, 2012 6:39 pm ] |
| Post subject: | Re: [ACT] XL7 4.24:1 Reduction Gears |
You would have to check the splines |
|
| Author: | thesupervisor [ Wed Sep 19, 2012 9:51 pm ] |
| Post subject: | Re: [ACT] XL7 4.24:1 Reduction Gears |
whats the best way count the splines from what point? |
|
| Author: | RIKSTR [ Thu Sep 20, 2012 10:56 am ] |
| Post subject: | Re: [ACT] XL7 4.24:1 Reduction Gears |
You will need to take the tcase off and count the output shaft on the gearbox. Maybe someone knows |
|
| Author: | SierraDan [ Fri Sep 21, 2012 8:16 pm ] |
| Post subject: | Re: [ACT] XL7 4.24:1 Reduction Gears |
a Rover LT230 would be a cheaper near equivalent in strength to an Atlas. |
|
| Author: | RIKSTR [ Sat Sep 22, 2012 4:22 pm ] |
| Post subject: | Re: [ACT] XL7 4.24:1 Reduction Gears |
Yea, I am sure the gears could handle it but a Vit case is chain driven and I don't thin the chain would handle sticky 40", I am guessing you are running sticky treps. If you are building a TT car I would cough up the cash and get an Atlas so you could run a digs too. |
|
| Author: | RIKSTR [ Fri Oct 19, 2012 6:04 pm ] |
| Post subject: | Re: [ACT] XL7 4.24:1 Reduction Gears |
These are still here and need to be sold |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|