no cause the starter bolts in in relation to the gearbox not the block
| auszookers.com https://www.auszookers.com/forum/ |
|
| 1.6 & 1.3 clutch https://www.auszookers.com/forum/viewtopic.php?f=5&t=3678 |
Page 1 of 1 |
| Author: | Damo [ Wed Dec 31, 2008 2:11 pm ] |
| Post subject: | 1.6 & 1.3 clutch |
What are the differences between g13 and g16 clutch/flywheels? |
|
| Author: | royce [ Wed Dec 31, 2008 2:16 pm ] |
| Post subject: | Re: 1.6 & 1.3 clutch |
G16 is 25mm bigger diameter G16 Flywheel is bigger, as well as being a lot thicker and heaver G16 throwout and the way it activates is pretty similar to 1.3 ones depending on which sierra one you have the spigots interchange and I think the splines may be similar I dont think you could sneak a 1.6 flywheel and clutch into a sierra bellhousing though |
|
| Author: | Damo [ Wed Dec 31, 2008 2:38 pm ] |
| Post subject: | Re: 1.6 & 1.3 clutch |
royce wrote: G16 is 25mm bigger diameter
G16 Flywheel is bigger, as well as being a lot thicker and heaver G16 throwout and the way it activates is pretty similar to 1.3 ones depending on which sierra one you have the spigots interchange and I think the splines may be similar I dont think you could sneak a 1.6 flywheel and clutch into a sierra bellhousing though So the clutch plate (eg, the one with the friction material on it) is 25mm bigger as well as the flywheel? Considering when you do a 1.6 swap into a Sierra the starters interchange, I thought that the flywheel would be the same overall diameter. |
|
| Author: | royce [ Wed Dec 31, 2008 2:51 pm ] |
| Post subject: | Re: 1.6 & 1.3 clutch |
no cause the starter bolts in in relation to the gearbox not the block
|
|
| Author: | Damo [ Wed Dec 31, 2008 3:43 pm ] |
| Post subject: | Re: 1.6 & 1.3 clutch |
royce wrote: no cause the starter bolts in in relation to the gearbox not the block
Ahhh that will explain it. So using the 1.6 flywheel wont work unless you use the 1.6 transmission. What about the tranny input splines? I've never seen a Vit manual in the flesh before. |
|
| Author: | royce [ Wed Dec 31, 2008 4:04 pm ] |
| Post subject: | Re: 1.6 & 1.3 clutch |
they may be the same, exedy site might say whats what 1.6 bellhousing comes off too, perhaps you could adapt it to the sierra box or get Joe to chop one down 
|
|
| Author: | joeblow [ Wed Dec 31, 2008 4:34 pm ] |
| Post subject: | Re: 1.6 & 1.3 clutch |
yes my children.....they are the same splines....on the 1.6 that is... |
|
| Author: | Damo [ Wed Dec 31, 2008 5:30 pm ] |
| Post subject: | Re: 1.6 & 1.3 clutch |
joeblow wrote: yes my children.....they are the same splines....on the 1.6 that is...
Schweet, thanks Dad 
|
|
| Author: | joeblow [ Wed Dec 31, 2008 6:49 pm ] |
| Post subject: | Re: 1.6 & 1.3 clutch |
dad?......now you makin it sound kinky
|
|
| Author: | Damo [ Wed Dec 31, 2008 7:22 pm ] |
| Post subject: | Re: 1.6 & 1.3 clutch |
joeblow wrote: dad?......now you makin it sound kinky you started it  joeblow wrote: yes my children.....
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|