I'm pretty sure that Pootrol rear arm bushes will fit
I'll test soon.
| auszookers.com https://www.auszookers.com/forum/ |
|
| How to fit radius arm bushes on Jimny? https://www.auszookers.com/forum/viewtopic.php?f=5&t=34562 |
Page 1 of 1 |
| Author: | bigdogdazza [ Sun Jul 29, 2012 8:46 am ] |
| Post subject: | How to fit radius arm bushes on Jimny? |
Hi guys another question for the Jimny gurus! Just as the title says, I fitted a 3" lift kit yesterday to the Jimny and drop radius arms came with poly bushes already fitted but my rear radius arms are flogged out badly! Need some advice on how to remove and install replacement bushes. The car handles loose in the rear like it has 5psi in rear tyres they are chopped out that bad and it's a worry to drive. |
|
| Author: | zooky08 [ Sun Jul 29, 2012 12:03 pm ] |
| Post subject: | Re: How to fit radius arm bushes on Jimny? |
Use a press to press them out and press the new ones in. |
|
| Author: | 31zook [ Sun Jul 29, 2012 4:54 pm ] |
| Post subject: | Re: How to fit radius arm bushes on Jimny? |
I'm pretty sure that Pootrol rear arm bushes will fit I'll test soon.
|
|
| Author: | bigdogdazza [ Sun Jul 29, 2012 7:20 pm ] |
| Post subject: | Re: How to fit radius arm bushes on Jimny? |
Hmmm now finding a press will be a mission! Will front radius arms fit as a replacement on the back? My front arms have great bushes in them but I have replaced the arms with drop radius arms so now they are kicking back relaxing in the shed. |
|
| Author: | KEENSY85 [ Sun Jul 29, 2012 7:41 pm ] |
| Post subject: | Re: How to fit radius arm bushes on Jimny? |
u in bris i could press them for free |
|
| Author: | Fatzook [ Sun Jul 29, 2012 9:49 pm ] |
| Post subject: | Re: How to fit radius arm bushes on Jimny? |
KEENSY85 wrote: u in bris i could press them for free Don't be so quick to offer your services for this job. These bushes can be a right C*!T to get out......even with a press. 
|
|
| Author: | monley [ Sun Jul 29, 2012 10:20 pm ] |
| Post subject: | Re: How to fit radius arm bushes on Jimny? |
I used a hammer and cold chisel to get the old one's out and a bit of heat, hammer and plate to get the new one's in.... |
|
| Author: | Dec [ Sun Jul 29, 2012 10:42 pm ] |
| Post subject: | Re: How to fit radius arm bushes on Jimny? |
I have a piece of steel perfectly lathed to push the bushes out/in if you get desperate. If they're the same as a sj80 coily that is. |
|
| Author: | bigdogdazza [ Mon Jul 30, 2012 3:03 am ] |
| Post subject: | Re: How to fit radius arm bushes on Jimny? |
Thanks heaps guys for the offer of help and tools! I reckon I will probably just rip the radius arms out and go door knocking on workshops until I find one with a press willing to do it for me........couldn't cost to much surely?? Unless someone willing to help near central coast nsw and is up for some free cold ones? I got my brother to grab the back wheel on the jimny and Rock it back and forward and can clearly see the whole diff moving forward and back on the radius arms! Hmmm don't think I will drive it at all until job done, just asking for mechanical failure or worse.... A wreck! |
|
| Author: | squibby [ Mon Jul 30, 2012 1:09 pm ] |
| Post subject: | Re: How to fit radius arm bushes on Jimny? |
monley wrote: I used a hammer and cold chisel to get the old one's out and a bit of heat, hammer and plate to get the new one's in.... I done this before now as well to get the old ones out. Its easy as pie if you have a SDS Drill that you can use in chisel mode. You can bodge pressing the new ones in with a decent Vice if you have one. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|