| auszookers.com https://www.auszookers.com/forum/ |
|
| G16b to H25A conversion https://www.auszookers.com/forum/viewtopic.php?f=5&t=30356 |
Page 1 of 1 |
| Author: | swifty_ano [ Sat Feb 11, 2012 11:26 am ] |
| Post subject: | G16b to H25A conversion |
Hi all, Over the years, I have heard of people fitting the H25a and H27A into a normal vitara/Tracker. However, I have never seen a thread of the actual conversion and what is neccessary. Does anyone know what needs to be done....obviously engine mounts How about Gearbox mounts? What gearbox do I use (GV or mine)? whats the difference in gearbox/t-case lengths? (will I need to move the gearbox back..new tailshafts etc) Fuel pump? is the stock tank able to cater? Any threads containing this conversion would be ever so helpful! Regards, Swifty |
|
| Author: | zukmeista [ Sat Feb 11, 2012 11:36 am ] |
| Post subject: | Re: G16b to H25A conversion |
Why not use a J20A? They came out it Vits so it might be an easier swap? |
|
| Author: | swifty_ano [ Sat Feb 11, 2012 11:56 am ] |
| Post subject: | Re: G16b to H25A conversion |
If I am going to swap, I want to make it worth the effort. I mean a 2L would be good but a 2.5 would be much better. Also, I have a front cut available very cheap |
|
| Author: | swifty_ano [ Sat Feb 11, 2012 11:57 am ] |
| Post subject: | Re: G16b to H25A conversion |
I am also under the impression the J20a has the same block? I may be wrong...its only hear say |
|
| Author: | rummy1 [ Sat Feb 11, 2012 12:34 pm ] |
| Post subject: | Re: G16b to H25A conversion |
swifty_ano wrote: If I am going to swap, I want to make it worth the effort. I mean a 2L would be good but a 2.5 would be much better. Also, I have a front cut available very cheap I'll buy the g16b from you if your going to do the conversion mate. all i need is the engine, i have the rest |
|
| Author: | atari4x4 [ Sat Feb 11, 2012 12:47 pm ] |
| Post subject: | Re: G16b to H25A conversion |
it's been done on here, check out threads made by dezook in the rigs section. i can't see how they are going to be the same block... J20a is a 4cyl the H20a, H25a, H27a are all V6's & the G series blocks are different again eg G13 & G16. your CV's are going to love the extra power. 
|
|
| Author: | swifty_ano [ Sat Feb 11, 2012 12:52 pm ] |
| Post subject: | Re: G16b to H25A conversion |
atari4x4 wrote: it's been done on here, check out threads made by dezook in the rigs section. i can't see how they are going to be the same block... J20a is a 4cyl the H20a, H25a, H27a are all V6's & the G series blocks are different again eg G13 & G16. your CV's are going to love the extra power. Very true......must have read it wrong...maybe block size or mounting points? Oh, and CV's have been taken care of 
|
|
| Author: | JrZook [ Sat Feb 11, 2012 1:07 pm ] |
| Post subject: | Re: G16b to H25A conversion |
swifty_ano wrote: atari4x4 wrote: it's been done on here, check out threads made by dezook in the rigs section. i can't see how they are going to be the same block... J20a is a 4cyl the H20a, H25a, H27a are all V6's & the G series blocks are different again eg G13 & G16. your CV's are going to love the extra power. Very true......must have read it wrong...maybe block size or mounting points? Oh, and CV's have been taken care of 4x2 racer 
|
|
| Author: | swifty_ano [ Sat Feb 11, 2012 7:51 pm ] |
| Post subject: | Re: G16b to H25A conversion |
JrZook wrote: swifty_ano wrote: atari4x4 wrote: it's been done on here, check out threads made by dezook in the rigs section. i can't see how they are going to be the same block... J20a is a 4cyl the H20a, H25a, H27a are all V6's & the G series blocks are different again eg G13 & G16. your CV's are going to love the extra power. Very true......must have read it wrong...maybe block size or mounting points? Oh, and CV's have been taken care of 4x2 racer Would be good. If I were to do this a 2jz would be my pick 
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|