| auszookers.com https://www.auszookers.com/forum/ |
|
| g16b timing https://www.auszookers.com/forum/viewtopic.php?f=5&t=26951 |
Page 1 of 1 |
| Author: | 4x4zook [ Thu Oct 20, 2011 5:22 am ] |
| Post subject: | g16b timing |
hey guys got a 97 g16b in my sierra. now i took it to my local mechanic to get it tuned after the motor was wired up. he set my timing to 2deg. i seem to remember reading somewere that it should be at 8 deg but i cant turn the dizzy anymre as its at its limit. so do i pull the dizzy out and try and get it to 8deg or leave it were he set it? |
|
| Author: | Drova [ Thu Oct 20, 2011 5:45 am ] |
| Post subject: | Re: g16b timing |
Stock timing is 5deg -+1deg |
|
| Author: | JrZook [ Thu Oct 20, 2011 6:05 am ] |
| Post subject: | Re: g16b timing |
Pull the dizzy out and move it a few teeth over so you are in the middle of the adjustment again. FSM says 5*BTDC base timing with the diagnostic plug bridged. I've just set mine till she starts to ping and brought her back a few degrees. Dan |
|
| Author: | steak_knife [ Thu Oct 20, 2011 6:24 am ] |
| Post subject: | Re: g16b timing |
JrZook wrote: Pull the dizzy out and move it a few teeth over so you are in the middle of the adjustment again.
FSM says 5*BTDC base timing with the diagnostic plug bridged. I've just set mine till she starts to ping and brought her back a few degrees. Dan Work's a treat!!! 
|
|
| Author: | 4x4zook [ Thu Oct 20, 2011 6:36 am ] |
| Post subject: | Re: g16b timing |
pulled the dizzy out a million times adjusting it but i still cant get it to 5deg. the closest i can get is 2 and 11.... might just get a round file and file a bit out of the dizzy so i can turn that tiny bit more.. |
|
| Author: | Scrawny [ Thu Oct 20, 2011 6:43 am ] |
| Post subject: | Re: g16b timing |
Something not right then. You should be able to get 8-10 in the middle of the adjustment |
|
| Author: | 4x4zook [ Thu Oct 20, 2011 6:57 am ] |
| Post subject: | Re: g16b timing |
what could be wrong? like i said iv pulled it out a million times but everytimei do i haveto turn it to the full adjustment to get 2 or 11 |
|
| Author: | 4x4zook [ Thu Oct 20, 2011 6:58 am ] |
| Post subject: | Re: g16b timing |
i rekon the mechanic must ov had the same problem so he just left it at 2deg. would filling the adjustment out a tiny bit work or not a good idea, theres a fair bit of meat on the sides. |
|
| Author: | royce [ Thu Oct 20, 2011 6:59 am ] |
| Post subject: | Re: g16b timing |
be gentler and pull it slowly till its jsut holding and youll feel it move over a single tooth |
|
| Author: | 4x4zook [ Thu Oct 20, 2011 7:35 am ] |
| Post subject: | Re: g16b timing |
i can feel it moving 1 tooth and still either wont start or be way way advanced |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|