use eye for starters u should be able to look straight through, this is how rooted mine was
| auszookers.com https://www.auszookers.com/forum/ |
|
| Is it straight?? https://www.auszookers.com/forum/viewtopic.php?f=5&t=21698 |
Page 1 of 1 |
| Author: | remydog05 [ Fri May 06, 2011 1:10 am ] |
| Post subject: | Is it straight?? |
I have a WT diff I have used in 2 of my NT sierras over the past few years. Its been given a bit of a hiding and i bought it from another bloke who had given it a bit of a hard time also. Im in the process of building my new LWB and Im thinking I should really confirm its straight and ready to go. Otherwise Im going to put the Cromo's locker and diff gears in it and drive it down the road and find its CRAP! So the magic question is, how can you tell its straight? Or is it a case of the old "high tech" machinery. |
|
| Author: | MrRocky [ Fri May 06, 2011 1:43 am ] |
| Post subject: | Re: Is it straight?? |
use eye for starters u should be able to look straight through, this is how rooted mine was
|
|
| Author: | remydog05 [ Fri May 06, 2011 7:23 am ] |
| Post subject: | Re: Is it straight?? |
So far from what I can tell its OK via the eye. |
|
| Author: | Fatzook [ Fri May 06, 2011 7:28 am ] |
| Post subject: | Re: Is it straight?? |
I use a laser level with dot function. Shoot through the centre of one side onto a piece of paper on the otherside. Its ok to be out by a little bit. |
|
| Author: | FullyZooked [ Fri May 06, 2011 7:50 am ] |
| Post subject: | Re: Is it straight?? |
MrRocky wrote: use eye for starters u should be able to look straight through, this is how rooted mine was
farrrk! |
|
| Author: | remydog05 [ Fri May 06, 2011 7:55 am ] |
| Post subject: | Re: Is it straight?? |
Fatzook wrote: I use a laser level with dot function. Shoot through the centre of one side onto a piece of paper on the otherside. Its ok to be out by a little bit.
Good thinking! I might get a piece of string and put it through and make it tight then have a look at some clearance from there, making sure the diff will be airbounre on stands or timber, etc. |
|
| Author: | Fatzook [ Fri May 06, 2011 8:09 am ] |
| Post subject: | Re: Is it straight?? |
remydog05 wrote: Fatzook wrote: I use a laser level with dot function. Shoot through the centre of one side onto a piece of paper on the otherside. Its ok to be out by a little bit. Good thinking! I might get a piece of string and put it That will work too. Get a mate to help. You can tie a can at each end of the string to help with communication 
|
|
| Author: | remydog05 [ Fri May 06, 2011 8:16 am ] |
| Post subject: | Re: Is it straight?? |
Fatzook wrote: remydog05 wrote: Fatzook wrote: I use a laser level with dot function. Shoot through the centre of one side onto a piece of paper on the otherside. Its ok to be out by a little bit. Good thinking! I might get a piece of string and put it That will work too. Get a mate to help. You can tie a can at each end of the string to help with communication  
Champagne comedy!~ |
|
| Author: | tombutt [ Fri May 06, 2011 8:18 am ] |
| Post subject: | Re: Is it straight?? |
Fatzook wrote: remydog05 wrote: Fatzook wrote: I use a laser level with dot function. Shoot through the centre of one side onto a piece of paper on the otherside. Its ok to be out by a little bit. Good thinking! I might get a piece of string and put it That will work too. Get a mate to help. You can tie a can at each end of the string to help with communication so this is why the ute is taking so long you using stone age technology |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|