| auszookers.com https://www.auszookers.com/forum/ |
|
| Wt diffs with nt spacing https://www.auszookers.com/forum/viewtopic.php?f=5&t=21069 |
Page 1 of 1 |
| Author: | zooky08 [ Sun Apr 17, 2011 12:40 am ] |
| Post subject: | Wt diffs with nt spacing |
Ok so I'm putting my wt diffs under a nt I had a read through bogfrog thread but being me I don't understand any of it 
I don't know why I don't get it 
Is there a better write up of what I'm after or is bogfrog thread the easiest write up there is? Links would be good Cheers |
|
| Author: | JrZook [ Sun Apr 17, 2011 12:51 am ] |
| Post subject: | Re: Wt diffs with nt spacing |
Um what dont you get? |
|
| Author: | zooky08 [ Sun Apr 17, 2011 12:56 am ] |
| Post subject: | Re: Wt diffs with nt spacing |
Were to weld the new perches on the diff( how far in) Maby I'll read it over nd over again till I get what he's saying |
|
| Author: | alien [ Sun Apr 17, 2011 12:59 am ] |
| Post subject: | Re: Wt diffs with nt spacing |
measure the distance between the center holes in the springs... now subtract that from the width of the diff housing end to end, divide that number by 2, then measure that far in on each side of the diff housing and you have the center point of your perch. make sure you get the pinion angle right. |
|
| Author: | steak_knife [ Sun Apr 17, 2011 1:02 am ] |
| Post subject: | Re: Wt diffs with nt spacing |
The w/t perch's need to be moved in 40mm, it is vital that they stay on the same plane, that's your caster adjustment...... the n/t r/h side perch is also a different shape to the l/h, being that it has to sit on the pumpkin a lil bit, so, i in the past have sacrificed the n/t housing's to save the perch buy cutting the tubing beside the perch, then take your time picking the pesrch of.. Or, buy a set of TSOR's perch's, have used em a couple of time's & love em, new steel is so mush nicer to work with.....& you don't have to be as careful with the ole one's..... |
|
| Author: | shep [ Sun Apr 17, 2011 1:02 am ] |
| Post subject: | Re: Wt diffs with nt spacing |
it is 45mm a side. from memory so best ya check yourself. edit: steeky beat me. don't trust my measurements 
|
|
| Author: | steak_knife [ Sun Apr 17, 2011 1:04 am ] |
| Post subject: | Re: Wt diffs with nt spacing |
Oh, I'm looking for some pic's I have some place in this computer...  may have to put my steelcap's on & re-boot it.....
|
|
| Author: | want33s [ Sun Apr 17, 2011 1:12 am ] |
| Post subject: | Re: Wt diffs with nt spacing |
Call in here and I'll show you the jig I made up for moving the perches... It is very basic but works well. |
|
| Author: | zooky08 [ Sun Apr 17, 2011 1:55 am ] |
| Post subject: | Re: Wt diffs with nt spacing |
Are you home today jas Might go for a drive |
|
| Author: | zooky08 [ Sun Apr 17, 2011 2:13 am ] |
| Post subject: | Re: Wt diffs with nt spacing |
So I think I worked it out wt diff spacing is 950 and nt diff spacing is 870 So 950 - 870 = 80 \ 2 is 40mm So perches have to be welded on wt diff 40mm in from center hole of the wt perch Is this all correct Also I already have the perches from fatzook |
|
| Author: | steak_knife [ Sun Apr 17, 2011 4:33 am ] |
| Post subject: | Re: Wt diffs with nt spacing |
zooky08 wrote: So I think I worked it out
wt diff spacing is 950 and nt diff spacing is 870 So 950 - 870 = 80 \ 2 is 40mm So perches have to be welded on wt diff 40mm in from center hole of the wt perch Is this all correct Also I already have the perches from fatzook Rear are wider than the front............ |
|
| Author: | zooky08 [ Sun Apr 17, 2011 4:53 am ] |
| Post subject: | Re: Wt diffs with nt spacing |
Rightio That was the rear I did Just then |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|