auszookers.com
https://www.auszookers.com/forum/

vitara twin stick,detent ball removal
https://www.auszookers.com/forum/viewtopic.php?f=5&t=15731		 Page 1 of 1
Author:  Fluffy [ Sat Oct 09, 2010 4:19 am ]
Post subject:  vitara twin stick,detent ball removal
can anyone point me in the right direction? I found info on here a while ago but can't seem to find it again.


I thought while the box is out I'll just do the mod, and run my twinsticks that i made ages ago

thanks
Fluff 8)
Author:  Fluffy [ Sat Oct 09, 2010 4:59 am ]
Post subject:  Re: vitara twin stick,detent ball removal
thanks guys found it.. that pesky little ball hidden away in there..
;)
Author:  Brett [ Sat Oct 09, 2010 5:41 am ]
Post subject:  Re: vitara twin stick,detent ball removal
so where is the pic of the twin stick you made up? i wouldn't mind doing one
Author:  Fluffy [ Sat Oct 09, 2010 7:44 am ]
Post subject:  Re: vitara twin stick,detent ball removal
Image
Author:  Joe [ Sat Oct 09, 2010 8:12 am ]
Post subject:  Re: vitara twin stick,detent ball removal
They look pretty flash mate :P
Author:  Brett [ Sat Oct 09, 2010 8:33 am ]
Post subject:  Re: vitara twin stick,detent ball removal
is that 2 levers cut and joined together?

that looks pretty flash
Author:  Fluffy [ Sat Oct 09, 2010 10:36 am ]
Post subject:  Re: vitara twin stick,detent ball removal
2 bits of 12 mm stainless i think... was a while ago... can take a few more pics tomorrow if yas want?
not that flash really. only made them cos i lost my original shifter/ to tight to buy one and had some spare time ;)
Author:  Brett [ Sat Oct 09, 2010 3:03 pm ]
Post subject:  Re: vitara twin stick,detent ball removal
that would be good thanks
Author:  Damo [ Sat Oct 09, 2010 8:48 pm ]
Post subject:  Re: vitara twin stick,detent ball removal
I like your knobs, Fluffy :oops:

You make them or purchase somewhere? I could use some like that.
Author:  Fluffy [ Sat Oct 09, 2010 9:07 pm ]
Post subject:  Re: vitara twin stick,detent ball removal
why thank you Damo.. ;)
I made them at another job when i had some down time.... so if I touch them all day my hand will go black, i should clear coat them.. .
Author:  Damo [ Sat Oct 09, 2010 10:02 pm ]
Post subject:  Re: vitara twin stick,detent ball removal
Did you CNC the lettering?

I could turn the knobs but have to use something dodgy like a letter punch :lol:
Author:  Fluffy [ Sun Oct 10, 2010 6:35 am ]
Post subject:  Re: vitara twin stick,detent ball removal
yeah did it on a cnc.you could do it on a manual mill with a fine cutter and a steady hand ;). maybe take it to an engraver?
I took pics.. gotta go out and put it back together then
I'll post them either tonight or Wednesday night
Author:  Fluffy [ Sat Oct 16, 2010 8:15 pm ]
Post subject:  Re: vitara twin stick,detent ball removal
pics for ya brett
pretty sure it was 2 lengths of 12mm or 1/2 stainless rod..
one thing i had problems with is one snapped on the pivot pin.. but since been welded
Fluff
Author:  zuk94 [ Sun Oct 17, 2010 3:21 am ]
Post subject:  Re: vitara twin stick,detent ball removal
What's the benefit that's worth going to all the trouble.
Author:  Proxy [ Tue Oct 19, 2010 11:19 am ]
Post subject:  Re: vitara twin stick,detent ball removal
this looks really cool, does this make it available to select low whilst in 2wd?
Author:  Fluffy [ Wed Oct 20, 2010 12:50 am ]
Post subject:  Re: vitara twin stick,detent ball removal
Proxy wrote:
does this make it available to select low whilst in 2wd?

yep if you remove the lil detent ball in the transfer

:)
Author:  Proxy [ Wed Oct 20, 2010 11:47 am ]
Post subject:  Re: vitara twin stick,detent ball removal
Fluffy wrote:
Proxy wrote:
does this make it available to select low whilst in 2wd?

yep if you remove the lil detent ball in the transfer

:)


can something like this be done in the sierra? and where do you find it usefull?
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/