| auszookers.com https://www.auszookers.com/forum/ |
|
| wheel cyl https://www.auszookers.com/forum/viewtopic.php?f=37&t=31210 |
Page 1 of 1 |
| Author: | Shandy [ Fri Mar 16, 2012 5:24 am ] |
| Post subject: | wheel cyl |
Hi there. I just got some wheel cylinder for the back of my 1.3 84 model sierra and they are differant part numberes left and right. They look the same and I thought they were. I even pulled them apart cause I was certain that they were the same. My question is: are they the same left and right? I'm sure it's an easy question for the omnipotent ones out there. LOL. |
|
| Author: | fully sick coily [ Fri Mar 16, 2012 6:01 am ] |
| Post subject: | Re: wheel cyl |
what do you mean by ''wheel cylinders" |
|
| Author: | Joshyboy26 [ Fri Mar 16, 2012 6:58 am ] |
| Post subject: | Re: wheel cyl |
one is left and one is right because the brake line comes into your drivers side then goes across from that to the other one. so only the passenger side has a bleed nipple on it. if you look at them you should have one with a bleed nipple and one with out. a wheel cylinder is much like a caliper but for pushing the brake shoes in drums apart instead of pushing brake pads together |
|
| Author: | Scrawny [ Fri Mar 16, 2012 7:11 am ] |
| Post subject: | Re: wheel cyl |
^^^^^^ What this bloke said |
|
| Author: | Shandy [ Fri Mar 16, 2012 5:56 pm ] |
| Post subject: | Re: wheel cyl |
On the late models I think the brake line goes from one side to the other, horizontal split system. But this has individual lines. |
|
| Author: | Joshyboy26 [ Sat Mar 17, 2012 6:56 am ] |
| Post subject: | Re: wheel cyl |
Maybe someone before you has changed it? I dunno then maybe someone else a bit more knowledgeable will pipe up haha. |
|
| Author: | Scrawny [ Sat Mar 17, 2012 8:44 am ] |
| Post subject: | Re: wheel cyl |
Take them back then. I think the earlier Sierras did have individual lines |
|
| Author: | steve [ Mon Mar 19, 2012 8:22 am ] |
| Post subject: | Re: wheel cyl |
I think they're the same left and right you just put the bleed valve in one side instead of the brake line for the later model ones, and just put a bleed valve in each side for the early model ones? |
|
| Author: | Scrawny [ Mon Mar 19, 2012 8:26 am ] |
| Post subject: | Re: wheel cyl |
steve wrote: I think they're the same left and right you just put the bleed valve in one side instead of the brake line for the later model ones, and just put a bleed valve in each side for the early model ones? Na, the line and nipple seats are different |
|
| Author: | steve [ Mon Mar 19, 2012 8:30 am ] |
| Post subject: | Re: wheel cyl |
ahh ok, i think it still works though ? I've probably used the wrong ones on the wrong sides at various times. |
|
| Author: | Shandy [ Tue Mar 20, 2012 9:28 pm ] |
| Post subject: | Re: wheel cyl |
Thank you. That was what i was thinkin. I'll have to look closer. Just whacked em on the shelf till I get my diff back. I dont mind checkin the brake fluid before I head to work. Pretty lazy like that! |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|