auszookers.com
https://www.auszookers.com/forum/

need help!!!!!
https://www.auszookers.com/forum/viewtopic.php?f=37&t=31124		 Page 1 of 1
Author:  fully sick coily [ Mon Mar 12, 2012 4:08 pm ]
Post subject:  need help!!!!!
ok so i was wondering what fairly easy mods there are for a coily :?

also is it very hard to fit a bodylift or coil spacers?

and would a solid t'case mount be better or not?
Author:  rustyzook [ Mon Mar 12, 2012 4:24 pm ]
Post subject:  Re: need help!!!!!
bl is easy, this is the build section not chat, so is this a build page of yours? if you do a search you may find your answers.
Author:  fully sick coily [ Mon Mar 12, 2012 7:07 pm ]
Post subject:  Re: need help!!!!!
where or how do i get to this build section?
Author:  fritter [ Mon Mar 12, 2012 7:29 pm ]
Post subject:  Re: need help!!!!!
For body lift have a look here: viewtopic.php?f=15&t=15518
They come with instructions. As far as coil spacers are concerned they are really easy to fit. At least they were on my vit.
PM Bruce. He I think he sells spacers, not sure about coily's though.
As for legalities in QLD? No idea.. Maybe one of the QLDer's could answer that.
Cheers
Author:  Fatzook [ Mon Mar 12, 2012 9:52 pm ]
Post subject:  Re: need help!!!!!
I've got coily spacers here. ( they are Bruces brand )

let me know if you need some.
Author:  fully sick coily [ Tue Mar 13, 2012 4:16 am ]
Post subject:  Re: need help!!!!!
thanks guys
fatzook: how much do you charge for coil spacers?

also what easy mods ase out there?
Author:  abclarke [ Tue Mar 13, 2012 5:32 am ]
Post subject:  Re: need help!!!!!
Really depends what you define as easy? Cheap? Quick? Simple?

What might be easy for one person might be hard for another.
Author:  fully sick coily [ Tue Mar 13, 2012 6:45 am ]
Post subject:  Re: need help!!!!!
Basicly any fairly cheap mods that dont involve machining
Would be great

So far iv got:
Removed swaybar
30x10 buckshots
Alloy bar and roll bar
Spotties
Pioneer system
Revers light
And extended bumps

What els am i able to do?
Any help is apreciated
Author:  stewy91 [ Tue Mar 13, 2012 5:21 pm ]
Post subject:  Re: need help!!!!!
body lift is fairly simple but it must be approved in Queensland so it has to go over the pits to ensure it is done correctly.
Author:  fully sick coily [ Tue Mar 13, 2012 7:43 pm ]
Post subject:  Re: need help!!!!!
does it cost much?
to get aproved?
Author:  Rusho [ Tue Mar 13, 2012 7:48 pm ]
Post subject:  Re: need help!!!!!
fully sick coily wrote:
does it cost much?
to get aproved?


Under $250, approval you will need to book into DOT. Bolt on standard tyres, sway bar and a general tidy up of EVERYTHING that isn't in a roadworthy condition 8)
Author:  stewy91 [ Tue Mar 13, 2012 7:53 pm ]
Post subject:  Re: need help!!!!!
its also a good idea to degrease and give everything a good clean before you take it so no oil leaks or any other faults can be found
Author:  fully sick coily [ Tue Mar 13, 2012 8:35 pm ]
Post subject:  Re: need help!!!!!
oops!!!
i no longer have stock wheels :(
can i just put legal tyres on my sunraiers?

is that $250 inc bodylift?
Author:  Rusho [ Tue Mar 13, 2012 8:41 pm ]
Post subject:  Re: need help!!!!!
BL is $220 from this guy 8)

viewtopic.php?f=15&t=15518

90% sure the DOT appointment is free, but I could be wrong
Author:  Zook_Fan [ Tue Mar 13, 2012 8:43 pm ]
Post subject:  Re: need help!!!!!
DOT appointment is around $70 per attempt but if you fail generally they don't charge you for a second
Author:  fully sick coily [ Wed Mar 14, 2012 4:14 am ]
Post subject:  Re: need help!!!!!
so will it get mod plated?

and can i have this on my car with my p's
( modified vehicle )
Author:  Zook_Fan [ Wed Mar 14, 2012 9:43 am ]
Post subject:  Re: need help!!!!!
No mod plate, you get a certificate to say it has passed and that has to stay in the vehicle at all times. No mod plates do not effect driving as p plater unless they are performance rated (forced induction, engine swap, etc).
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/