well finally i have got myself a pipe bender, and did my first job with it today....
new cistern and plumbing
| auszookers.com https://www.auszookers.com/forum/ |
|
| got myself a pipe bender ! https://www.auszookers.com/forum/viewtopic.php?f=14&t=7958 |
Page 1 of 1 |
| Author: | steve [ Sat Nov 14, 2009 8:55 pm ] |
| Post subject: | got myself a pipe bender ! |
well finally i have got myself a pipe bender, and did my first job with it today.... new cistern and plumbing
|
|
| Author: | royce [ Sat Nov 14, 2009 9:03 pm ] |
| Post subject: | Re: got myself a pipe bender ! |
are you going to polish that copper? |
|
| Author: | steak_knife [ Sat Nov 14, 2009 9:04 pm ] |
| Post subject: | Re: got myself a pipe bender ! |
That look's shit house steve 
|
|
| Author: | royce [ Sat Nov 14, 2009 9:20 pm ] |
| Post subject: | Re: got myself a pipe bender ! |
whats the half flush rating on that one? |
|
| Author: | steve [ Sat Nov 14, 2009 9:20 pm ] |
| Post subject: | Re: got myself a pipe bender ! |
royce, yer maybe i should paint it with some clear coat. |
|
| Author: | royce [ Sat Nov 14, 2009 9:23 pm ] |
| Post subject: | Re: got myself a pipe bender ! |
Hammer tone |
|
| Author: | atari4x4 [ Sat Nov 14, 2009 10:00 pm ] |
| Post subject: | Re: got myself a pipe bender ! |
that looks like a shit job... |
|
| Author: | steve [ Sat Nov 14, 2009 10:13 pm ] |
| Post subject: | Re: got myself a pipe bender ! |
hah yeah , bit of toilet humour there 
|
|
| Author: | Scrawny [ Sat Nov 14, 2009 10:20 pm ] |
| Post subject: | Re: got myself a pipe bender ! |
Bout time you replaced the old dunny!! |
|
| Author: | Damo [ Sat Nov 14, 2009 11:14 pm ] |
| Post subject: | Re: got myself a pipe bender ! |
Shit of a job |
|
| Author: | Saam [ Sat Nov 14, 2009 11:17 pm ] |
| Post subject: | Re: got myself a pipe bender ! |
i'd rather do a poo than install a toilet.. yeah.. hmm |
|
| Author: | andypandy [ Sat Nov 14, 2009 11:28 pm ] |
| Post subject: | Re: got myself a pipe bender ! |
looks shit (pun intended) but not bad for ur first go |
|
| Author: | andrewa [ Sun Nov 15, 2009 1:16 am ] |
| Post subject: | Re: got myself a pipe bender ! |
thats the shit steve. going into the freelance plumbing buisness are we steve. 
|
|
| Author: | brendan [ Sun Nov 15, 2009 2:24 am ] |
| Post subject: | Re: got myself a pipe bender ! |
thats tube not pipe
could have use chrome plated copper and fittings, look better, |
|
| Author: | just_cruizin [ Sun Nov 15, 2009 6:02 am ] |
| Post subject: | Re: got myself a pipe bender ! |
Stainless braided hose always look bling. Have you christen it yet with an AGB or some Indian. |
|
| Author: | MacDaddy [ Sun Nov 15, 2009 9:59 am ] |
| Post subject: | Re: got myself a pipe bender ! |
steve wrote: well finally i have got myself a pipe bender, and did my first job with it today....
new cistern and plumbing Hi Steve, Seeing as i dont see any oxy torch marks on the copper, i dont think it was the spring type pipe bender, i am guessing its the two pully type benders that hold the pipe inside, and you pull on the two arms and the pipe bends without squashing flat... if you can understand that... I used to be a Refrigeration Technician before i became a Comp Techie, so i used both types of copper tube benders quite often, he he... did you have the flaring tool as well ? Cheers |
|
| Author: | steve [ Sun Nov 15, 2009 11:53 am ] |
| Post subject: | Re: got myself a pipe bender ! |
just_cruizin wrote: Stainless braided hose always look bling.
Have you christen it yet with an AGB or some Indian. I was going to get the stainless braided hoses, but i think that would be a really bad idea to have in the toilet with regards to cleanliness. No hasn't been completely tested yet. Macbear, yeah it's a two arm bender. Don't need a flaring tool for these things, the olives (plastic ring) on the tube/pipe squish it when you tighten the nut. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|