auszookers.com
https://www.auszookers.com/forum/

Rock sliders sidesteps for GV
https://www.auszookers.com/forum/viewtopic.php?f=14&t=47238		 Page 1 of 1
Author:  zoukshin [ Fri Aug 01, 2014 8:31 am ]
Post subject:  Rock sliders sidesteps for GV
Just a dump of photos of my UNIFINISHED project (was stolen 2 days ago. rebuild pending)

Initial CAD
Image
Image

New toy - stick inverter
Image

Chassis clamps
Image
Image

First rough assembly after bending - did not use sand, bend went wrong. Use sand, it helps a lot.
Image
Image

What it would look like really
Image

Notching setup. Too much vibration, kills the saw prematurely, but it works for cheap. Jig allows 45 degree cuts
Image
Image

Global view
Image

Cozy bending, packed with sand. Great results.
Image
Image
Image

Bender mod to bend back my enthusiasm
Image
Image

Last photo of it before it was stolen
Image

Well obviously it was not finished, and am pissed off I was robbed. But I'll do it again. I have the whole CAD and concept proven by now (not track tested)
Next time I will buy steel, and not re-use discarded galvanized pipes, cause they are crap to weld (even ground) and the remaining galva is poisonous.

Also if you come around someone with these sliders (they have M marked steel and one of the sliders has no front element welded) make sure to say hi for me.

Full album: http://imgur.com/a/dh6tk
Author:  henno [ Fri Aug 01, 2014 8:34 am ]
Post subject:  Re: Rock sliders sidesteps for GV
What the actual fuck? Some jerk-off stole some unfinished sliders? These are pretty unique and there aren't too many GVs around with sliders so who knows what they'd do with them.

Where were they nicked from?
Author:  zoukshin [ Fri Aug 01, 2014 8:41 am ]
Post subject:  Re: Rock sliders sidesteps for GV
nicked from my park spot down my building. Access card required to get there. We had multiple incidents over the years.
Unfinished and rough as - the photos do a good job hiding my shit welds.
I guess with a bit of work you could use them for any 4wd but it wouldn't fit well, they are 160 long, very GV specific.
So, yeah, very frustrated.

Will have to re-do it all, this time with proper steal [EDIT] Steel - aha.
If anyone can direct me to a good supplier around Brissy, I'll get going.
I need about 5 meters of 4mm thick 35mm diameter pipe. And 2 meters 5mmx40mm bar. Maybe some checker and stuff.

I ain't given up. too pissed off for that.
Author:  henno [ Fri Aug 01, 2014 8:45 am ]
Post subject:  Re: Rock sliders sidesteps for GV
No CCTV for your building?
Author:  pete_79 [ Fri Aug 01, 2014 8:49 am ]
Post subject:  Re: Rock sliders sidesteps for GV
Well that's got to be a new low.... Grubs!

Keep an eye out for roof racks too, they might not work as sliders for other cars but can see how someone might think they would look good as sides on a flat roof rack.
Author:  zoukshin [ Fri Aug 01, 2014 9:20 am ]
Post subject:  Re: Rock sliders sidesteps for GV
no cctv. YET. maybe. years of discussions. Time to move out altogether. Get myself a shed with electrical fence, moats and some frikkin turrets.

Pete, these are steel, heavy bastards. you'd have to be mad to put that on your roof. Then again, whoever stole em is probably not the brightest.
Author:  Chop [ Fri Aug 01, 2014 12:09 pm ]
Post subject:  Re: Rock sliders sidesteps for GV
That's shit mate, I'd put money on it being drug dependent turds using it for scrap.
Author:  Ricey [ Fri Aug 01, 2014 7:36 pm ]
Post subject:  Re: Rock sliders sidesteps for GV
If these work well would you consider fabricating more to sell?
Author:  jtraf [ Fri Aug 01, 2014 11:31 pm ]
Post subject:  Re: Rock sliders sidesteps for GV
I make and sell rails if that is easier......

Image
Image
Image
Image
Author:  Ricey [ Sun Aug 03, 2014 8:09 am ]
Post subject:  Re: Rock sliders sidesteps for GV
Do these work as sliders too tho?
Author:  jtraf [ Sun Aug 03, 2014 9:36 pm ]
Post subject:  Re: Rock sliders sidesteps for GV
Yep they are made from 40NB Australian Pipe with 3.2mm wall thickness. Mounted right you can use them as a highlift location
Author:  zoukshin [ Mon Aug 04, 2014 9:12 am ]
Post subject:  Re: Rock sliders sidesteps for GV
jtraf, coincidentally just found yours on gumtree/ebay while looking for my missing ones.
Designing and building them is half the fun, with learning the howto techniques etc. - Mine were (and will be again) 33.7NB 3.2 Gauge.
Curious to know what you use for notching though ? clearly you have some experience making these.
Author:  jtraf [ Mon Aug 04, 2014 1:29 pm ]
Post subject:  Re: Rock sliders sidesteps for GV
JD2 Notcher with Bi-Metal Holesaws for notching.

There are cheaper ones on the market that may suit your needs though.
Author:  zoukshin [ Mon Aug 04, 2014 2:11 pm ]
Post subject:  Re: Rock sliders sidesteps for GV
http://jd2.com.au/notchers/tn-100.html clearly over my budget :D But I'll keep that in mind in case I need more fab done. I'll stick to my very DIY setup for now.
Am about to buy some steel with some bits pre-cut so hopefully I just have to bend, notch and weld. I want to see this thing DONE.
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/